- 您現在的位置：買賣IC網 > PDF目錄384661 > MAX323EJA (MAXIM INTEGRATED PRODUCTS INC) Precision, Single-Supply, SPST Analog Switches PDF資料下載
參數資料
| 型號： | MAX323EJA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Precision, Single-Supply, SPST Analog Switches |
| 中文描述： | DUAL 1-CHANNEL, SGL POLE SGL THROW SWITCH, CDIP8 |
| 封裝： | 0.300 INCH, CERAMIC, SDIP-8 |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 105K |
| 代理商： | MAX323EJA |
M
Prec ision, S ingle-S upply,
S PS T Analog S witc hes
6
_______________________________________________________________________________________
__________Applic ations Information
Logic Levels
The MAX323/MAX324/MAX325 are TTL compatible
when powered from a single +5V supply. When pow-
ered from other supply voltages, TTL compatibility is
not guaranteed, and the logic inputs should be driven
from rail to rail. For example, with a 15V supply, IN1
and IN2 should be driven low to 0V and high to 15V.
Similarly, with a 3.3V supply, IN1 and IN2 should be dri-
ven low to 0V and high to 3.3V
Driving IN1 and IN2 rail-to-rail minimizes power con-
sumption.
Analog S ignal Levels
Analog signals that range over the entire supply voltage
(V+ to GND) can be switched with very little change in
on-resistance over the entire voltage range (see Typical
Operating Characteristics). All the switches are bidirec-
tional, so NO_, NC_, and COM_ pins can be used as
either inputs or outputs.
Power-S upply S equenc ing
and Overvoltage Protec tion
Do not exceed the absolute maximum ratings, because
stresses beyond the listed ratings may cause permanent
damage to the devices.
Proper power-supply sequencing is recommended for
all CMOS devices. Always apply V+ before applying
analog signals or logic inputs, especially if the analog
or logic signals are not current-limited. If this sequenc-
ing is not possible, and if the analog or logic inputs are
not current-limited to <30mA, add a small-signal diode
(D1) as shown in Figure 1. If the analog signal can dip
below GND, add D2. Adding protection diodes reduces
the analog signal range to a diode-drop (about 0.7V)
below V+ (for D1), and to a diode-drop above ground
(for D2). Leakage is unaffected by adding the diodes.
On-resistance increases by a small amount at low sup-
ply voltages. Maximum supply voltage (V+) must not
exceed 17V.
Adding protection diodes causes the logic thresholds
to be shifted relative to the power-supply rails. This can
be significant when low supply voltages (5V or less) are
used. With a 5V supply, TTL compatibility is not guaran-
teed when protection diodes are added. Driving IN1
and IN2 all the way to the supply rails (i.e. to a diode-
drop higher than the V+ pin, or to a diode-drop lower
than the GND pin) is always acceptable.
Protection diodes D1 and D2 also protect against
some overvoltage situations. With Figure 1’s circuit, if
the supply voltage is below the absolute maximum rat-
ing, and if a fault voltage up to the absolute maximum
rating is applied to an analog signal pin, no damage
will result. For example, with a +5V supply, analog sig-
nals up to ±8V will not damage the circuit of Figure 1.
If only a single fault signal is present, the fault voltage
can rise to +17V or to -12V without damage occurring.
_____________________Pin Desc ription
POSITIVE SUPPLY
COM
NO
D2
D1
GND
Vg
V+
Figure 1. Overvoltage Protection Using Two External Blocking
Diodes
Normally Closed Analog Switch Terminal
(MAX324/MAX325)
NC2
Normally Open Analog Switch Terminal
(MAX323 only)
NO2
5
Ground
GND
4
Logic Inputs
IN2, IN1
3, 7
PIN
Analog Switch Common Terminal
COM1,
COM2
2, 6
Normally Closed Analog Switch Terminal
(MAX324 only)
NC1
Normally Open Analog Switch Terminal
(MAX323/MAX325)
NO1
1
FUNCTION
NAME
Positive Supply
V+
8
相關PDF資料 |
PDF描述 |
|---|---|
| MAX323MJA | Precision, Single-Supply, SPST Analog Switches |
| MAX3260 | 32-Bit Digital Signal Controller with Flash 100-LQFP -40 to 85 |
| MAX3261 | 32-Bit Digital Signal Controller with Flash 100-LQFP -40 to 125 |
| MAX3261CCJ | 32-Bit Digital Signal Controller with Flash 100-LQFP -40 to 125 |
| MAX3261ECJ | Single +5V, Fully Integrated, 1.25Gbps Laser Diode Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX323EPA | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX323EPA+ | 功能描述:模擬開關 IC Precision Single Supply SPST RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX323ESA | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX323ESA+ | 功能描述:模擬開關 IC Precision Single Supply SPST RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX323ESA+T | 功能描述:模擬開關 IC Precision Single Supply SPST RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
發布緊急采購，3分鐘左右您將得到回復。