- 您現在的位置：買賣IC網 > PDF目錄374612 > S-4543A (Seiko Instruments Inc.) Dot Matrix LCD Driver(點陣LCD驅動器) PDF資料下載
參數資料
| 型號： | S-4543A |
| 廠商： | Seiko Instruments Inc. |
| 英文描述： | Dot Matrix LCD Driver(點陣LCD驅動器) |
| 中文描述： | 點陣LCD驅動器（點陣液晶驅動器） |
| 文件頁數： | 11/27頁 |
| 文件大?。?/td> | 163K |
| 代理商： | S-4543A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
Dot Matrix LCD Driver
S-4543A
10
Seiko Instruments Inc.
OPERATION
1.Power-on and off
1.1 Power-on
After power-on, set the default parameters through command input. Input the display off command immediately
after the CPU starts. Set other parameters in order until the display starts. The C3/2X pin must be connected to
V
DD
or V
SS
for use. The recommended procedures after power-on, are as follows:
1. Display ON/OFF
D0: 0
Display OFF
2. Full display ON/OFF
D0: 0
Full display OFF (start of oscilation)
3. End command input
4. ADC selection
5. Display start line
6. Page address "0000"
7. Column address "0000000"
8. Write display data *
9. Display ON
D0: 1
Display ON (start of display)
* After power-on, write display data to all addresses of the display RAM before setting the display to ON because
display RAM is not defined at start up.
1.2 Power-off
Power-off after setting display OFF through a CPU command. The recommended procedures at power-off are
as follows:
1. Display ON/OFF
D0: 0
Display OFF
Note:
After power-on, the parameters except display data RAM are initialized by the operation of the
internal reset circuit. The reset circuit operates at the positive edge of the power-on from ground
voltage level. The operation of the reset circuit can not be guaranteed when the power does not rise
from ground voltage level because of residual voltage from a momentary power failure or continuous
power-on operations.
2.MPU Interface Select
In the S-4543A series, the 8-bit interface or serial interface can be selected.
Table 10 MPU Interface Select
P/SX pin logic
MPU interface
H
68-family interface
L
Serial interface
Note: The displayed data write instruction and displayed data read instruction cannot be executed with E1 and E2
active at the same time.
相關PDF資料 |
PDF描述 |
|---|---|
| S-4544A | LCD Controller-Driver With Built-in 8-Bit and Serial Interfaces(內置8位和串行接口的LCD控制器-驅動器) |
| S-4561A | LCD Controller-Driver With Built-in Serial and Parallel interfaces(內置串行和并行接口的LCD控制器-驅動器) |
| S-4562A | LCD CONTROLLER DRIVER |
| S-4601A | 64-bit THERMAL HEAD DRIVER |
| S-4602A | CMOS Thermal Print Head Driver Containing a 64-Bit Shift Register and a Latch(內置一個64位移位寄存器和一個鎖存器的CMOS 熱敏打印頭驅動器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S-4544A | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:LCD Controller-Driver |
| S4545 | 制造商:BOTHHAND 制造商全稱:Bothhand USA, LP. 功能描述:T1/CEPT/ISDN-PRI TRANSFORMER |
| S455-003 | 制造商:Tripp Lite 功能描述:SCSI ULTRA2/U160/U320 LVD/SE CABLE - CHDC168(M) / HD68(M) - - Bulk |
| S455-006 | 功能描述:CABLE SCSI VHDCI68M/HD68M 6' RoHS:是 類別:電纜組件 >> 系列間適配器電纜 系列:- 標準包裝:1 系列:- 其它名稱:VS-M12MSD-RJ45-933-B/ 5,0VS-M12MSD-RJ45-933-B/5,0 |
| S455-010 | 功能描述:CABLE SCSI VHDCI68M/HD68M 10' RoHS:是 類別:電纜組件 >> 系列間適配器電纜 系列:- 標準包裝:1 系列:- 其它名稱:VS-M12MSD-RJ45-933-B/ 5,0VS-M12MSD-RJ45-933-B/5,0 |
發布緊急采購，3分鐘左右您將得到回復。