- 您現在的位置：買賣IC網 > PDF目錄363223 > NCP348AE (ON SEMICONDUCTOR) Positive Overvoltage Protection Controller with Internal Low RON NMOS FET and Status FLAG(具有內部低Ron NMOS FET和狀態標志位的正電壓過壓保護控制器) PDF資料下載
參數資料
| 型號： | NCP348AE |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | Positive Overvoltage Protection Controller with Internal Low RON NMOS FET and Status FLAG(具有內部低Ron NMOS FET和狀態標志位的正電壓過壓保護控制器) |
| 中文描述： | 積極過壓保護控制器，內置低辛烷值NMOS管FET和狀態標志（具有內部低羅恩NMOS管場效應管和狀態標志位的正電壓過壓保護控制器） |
| 文件頁數： | 10/13頁 |
| 文件大?。?/td> | 280K |
| 代理商： | NCP348AE |
NCP348, NCP348AE
http://onsemi.com
10
Undervoltage Lockout (UVLO)
To ensure proper operation under any conditions, the
device has a builtin undervoltage lockout (UVLO) circuit.
During V
in
positive going slope, the output remains
disconnected from input until V
in
voltage is below 3.25 V
(NCP348MTT version), plus hysteresis, nominal. The
FLAG
output is tied to low as long as V
in
does not reach
UVLO threshold. This circuit has a 50 mV hysteresis to
provide noise immunity to transient condition. Additional
UVLO thresholds ranging from UVLO can be
manufactured. (See Selection Guide on page 12) Contact
your ON Semiconductor representative for availability.
Overvoltage Lockout (OVLO)
To protect connected systems on V
out
pin from
overvoltage, the device has a builtin overvoltage lockout
(OVLO) circuit. During overvoltage condition, the output
remains disabled as long as the input voltage exceeds 6.4 V
typical (NCP348MTT version). Additional OVLO
thresholds ranging from OVLO can be manufactured. (See
Selection Guide on page 12) Contact your ON
Semiconductor representative for availability.
FLAG
output is tied to low until V
in
is higher than OVLO.
This circuit has a 100 mV hysteresis to provide noise
immunity to transient conditions
.
FLAG
Output
The NCP348 provides a FLAG output, which alerts
external systems that a fault has occurred.
This pin is tied to low as soon the OVLO threshold is
exceeded or when the V
in
level is below the UVLO
threshold. When V
in
level recovers normal condition,
FLAG is held high, keeping in mind that an additional
50 ms delay has been added between available output and
FLAG = high. The pin is an open drain output, thus a pull
up resistor (typically 1 M , minimum 10 k ) must be
added to V
bat
. Minimum V
bat
supply must be 2.5 V. The
FLAG level will always reflects V
in
status, even if the
device is turned off (EN = 1).
EN
Input
To enable normal operation, the
EN
pin shall be forced
to low or connected to ground. A high level on the pin,
disconnects OUT pin from IN pin.
EN
does not overdrive
an OVLO or UVLO fault.
Internal NMOS FET
The NCP348 includes an internal Low R
DS(on)
NMOS
FET to protect the systems, connected on OUT pin, from
positive overvoltage. Regarding electrical characteristics,
the R
DS(on)
, during normal operation, will create low losses
on V
out
pin.
As example: R
load
= 8.0 , V
in
= 5.0 V
Typical R
DS(on)
= 65 m
V
out
= 8 x 0.618 = 4.95 V
NMOS losses = R
DS(on)
x Iout
2
= 0.065 x 0.618
2
= 25 mW
I
out
= 618 mA
ESD Tests
The NCP348 input pin fully supports the IEC6100042.
1.0 F (minimum) must be connected between V
in
and
GND, close to the device.
That means, in Air condition, V
in
has a
protected input. In Contact condition, V
in
has
ESD protected input.
Please refer to Figure 19 to see the IEC 6100042
electrostatic discharge waveform.
15 kV ESD
8.0 kV
Figure 19. Electrostatic Discharge Waveform
PCB Recommendations
The NCP348 integrates a 2 amperes rated NMOS FET,
and the PCB rules must be respected to properly evacuate
the heat out of the silicon. The PAD1 is internally isolated
from the active silicon and should preferably be connected
to ground.
The PAD2 of the NCP348 package is connected
to the internal NMOS drain and can be used to increase the
heat transfer if necessary from an applications standpoint.
Depending upon the power dissipated in the application,
one can either use the PCB tracks connected to Pins 4 and
5 to evacuate heat, or make profit of the PAD2 area to add
extra copper surface to reduce the junction temperature
(See Figure 20).
Of course, in any case, this pad shall be not
connected to any other potential.
Figure 20 shows copper
area according to R
JA
and allows the design of the heat
transfer plane connected to PAD2.
相關PDF資料 |
PDF描述 |
|---|---|
| NCP3520 | LDO Regulator Controller |
| NCP3520DMR2G | LDO Regulator Controller |
| NCP3521 | LDO Regulator Controller |
| NCP360 | USB Positive Overvoltage Protection Controller with Internal PMOS FET and Status FLAG |
| NCP360MUTBG | USB Positive Overvoltage Protection Controller with Internal PMOS FET and Status FLAG |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP348AEMTTBG | 功能描述:監控電路 POS OVERVLTG PROTECT CONTROLLER RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| NCP348AEMTTBG-CUT TAPE | 制造商:ON 功能描述:NCP348AE Series 6.4 V Threshold 28 V Positive Overvoltage Protection Controller |
| NCP348AEMTTXG | 功能描述:監控電路 POS OVERVLTG PROTECT CONTROLLER RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| NCP348AEMUTBG | 功能描述:監控電路 POSTIVE OVP PRTCTION RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| NCP348GEVB | 功能描述:電源管理IC開發工具 EVALUATION BRD DEV RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。