參數資料
型號： NCP1239
廠商： ON SEMICONDUCTOR
英文描述： Low−Standby High Performance PWM Controller
文件頁數： 6/38頁
文件大?。?/td> 1145K
代理商： NCP1239
NCP1239
http://onsemi.com
6
PIN FUNCTION DESCRIPTION
Pin No.
Pin Name
Function
Pin Description
1
GTS
Shuts the PFC down in
standby
The standby detection block changes Pin 1 state in accordance to the mode
(standby or normal mode). Pin1 is designed to drive an external pnp transistor that
connects or disconnects the NCP1239’s V
CC
to the PFC’s.
2
REF5V
A 5V reference voltage
This pin helps to internally bias the controller but can also be used to power
surrounding logic gates for any purposes. The typical output current is 10 mA. This
voltage source is disabled during the circuit startup and latchedoff phases. A
100 nF filtering capacitor must be placed between Pin 2 and ground.
3
Fault Detect
Enables to permanently
shutdown the part
If the Pin 3 voltage exceeds 2.4 V, the circuit is permanently shut down. This pin
can be used to monitor the voltage across a thermistor in order to protect the
application from excessive heating and/or to detect an overvoltage condition.
4
Rt
Timing resistor
Pin 4 resistor allows a precise frequency programming. The circuit is optimized to
operate between 50 kHz and 150 kHz (NCP1239F) and between 100 kHz and
250 kHz (NCP1239V).
5
BrownOut
BrownOut
This pin receives a portion of the bulk capacitor to authorize operation above a
certain level of mains only. It also serves to elaborate an offset voltage on Pin 9
used for Over Power Compensation.
6
SS/Timer
Performs softstart and
fault timeout
During Power on and fault conditions, the capacitor connected to this pin ensures a
softstart period. When a fault is detected, this pin is internally brought high by a
current source. If 4.3 V are reached, the fault is confirmed and the circuit enters an
autorecovery burst mode, otherwise the pin goes back to a lower value and
oscillates to perform frequency jittering.
7
Skip Adjust
Adjust skip level
By adjusting the skipcycle level, it is possible to fight against noisy transformers
and modify the standby detection thresholds. Keep Pin 7 open to operate with the
default levels (skip threshold setpoint: 140 mV, normal mode recovery setpoint:
250 mV).
8
FB
Feedback signal
An optocoupler collector pulls this pin low to regulate
9
Over Power
Limit
(NCP1239F)
Enables a precise peak
current clamp and then an
accurate Over Power
Detection
This pin delivers a current proportional to V
pin5
, an image of the high voltage rail.
Inserting a resistor between Pin 9 and the current sense resistor, an offset
proportional to the input voltage is built. Such offset compensates the circuit and
power switch propagation delays for an accurate power limitation in the whole input
voltage range.
9
Max Duty
Cycle
(NCP1239V)
Enables to precisely
clamp the maximum
dutycycle.
This terminal sources a constant current. Connect a resistor between Pin 9 and
Ground to select the maximum dutycycle.
10
CS
The current sense input
This pin receives the primary current information via a sense element. By inserting
a resistor in series with this pin, it becomes possible to introduce ramp
compensation.
11
Ground
The IC ground
12
Drv
Drives the MOSFET
By offering up to +500 mA/800 mA peak, this pin lets you drive large Qg
MOSFET’s. It is clamped to 16 V maximum not to exceed the maximum
gatesource voltage of most power MOSFET’s.
13
V
CC
Supplies the controller
This pin accepts up to 36 V from an auxiliary winding.
14
NC
Creepage distance.
15
NC
Creepage distance.
16
HV
The highvoltage startup
This pin connects to the bulk capacitor to generate the startup current.
相關PDF資料
PDF描述
NCP1239FDR2 Low−Standby High Performance PWM Controller
NCP1239FDR2G Low−Standby High Performance PWM Controller
NCP1239VDR2 Low−Standby High Performance PWM Controller
NCP1239VDR2G Low−Standby High Performance PWM Controller
NCP1271 Soft−Skip Mode Standby PWM Controller with Adjustable Skip Level and External Latch
相關代理商/技術參數
參數描述
NCP1239D 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low-Standby High Performance PWM Controller
NCP1239F 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:AC-DC Offline Switching Controllers/Regulators
NCP1239FDR2 功能描述:電流型 PWM 控制器 Low Standby Power RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
NCP1239FDR2G 功能描述:電流型 PWM 控制器 Low Standby Power High Performance PWM RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
NCP1239V 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:AC-DC Offline Switching Controllers/Regulators
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*