參數資料
型號： NCP1239
廠商： ON SEMICONDUCTOR
英文描述： Low−Standby High Performance PWM Controller
文件頁數： 34/38頁
文件大?。?/td> 1145K
代理商： NCP1239
NCP1239
http://onsemi.com
34
315.4U
882.7U
1.450M
2.017M
2.585M
300.0M
200.0M
100.0M
0
25% of max Ip
Max peak
current
Figure 56.
The skipcycle takes place at low peak currents which guaranties noise free operation
PFC Inhibition in Standby
The circuit detects a light load condition by permanently
monitoring the skipcycle comparator activity: in normal
load condition this comparator keeps quiet. As soon as the
load strongly decreases, this comparator starts to toggle at a
low frequency rate: we are entering skipcycle and the
optocoupler operates in a digital manner, ON/OFF.
Figure 56 shows the way skipcycle is detected. In skip
mode, the feedback voltage oscillates around V
pin7
(If no
voltage is applied to the Pin 7, a 430 mV voltage source
supplies a default value through a high impedance resistor).
In these conditions, the skip comparator (“COMP1”) that
turns on and off (to adjust the skip mode bunches of pulses),
sets the standby detection latch. A second comparator
(“COMP2”) compares the feedback voltage (FB or V
pin8
) to
1.7*V
pin7
.
As long as the load keeps light, FB does not exceed
1.7*V
pin7
(i.e., 0.74 V typical if no voltage is forced to
Pin 7). A timer counts down and if COMP2 keeps high for
100 ms (typically with 390 nF on Pin 6), the NCP1239
considers that the system runs in the standby mode. Pin 1
turns high, a 10 k resistor tying the pin to V
CC
. If as shown
in Figure 39, Pin 1 directly drives a pnp transistor that is
connected between V
CC
and the PFC V
CC
, this switch turns
off in standby. As a result, this transistor stops feeding the
PFC V
CC
and ultimately shuts the PFC down.
As soon as FB exceeds 1.7*V
pin7
, the circuit leaves the
standby mode without any delay by forcing a 1 mA sinking
current source on Pin 1, that reactivates the pnp transistor
and then the PFC stage.
One can note that there is a 1/3 ratio between the actual
current setpoint and the feedback value FB. Therefore the
default thresholds for standby detection and normal mode
recovery (0.43 V, 0.74 V) actually corresponds to the
140 mV and 250 mV setpoints.
Figure 57.
A delay is inserted to avoid false tripping of the GTS signal
70%
相關PDF資料
PDF描述
NCP1239FDR2 Low−Standby High Performance PWM Controller
NCP1239FDR2G Low−Standby High Performance PWM Controller
NCP1239VDR2 Low−Standby High Performance PWM Controller
NCP1239VDR2G Low−Standby High Performance PWM Controller
NCP1271 Soft−Skip Mode Standby PWM Controller with Adjustable Skip Level and External Latch
相關代理商/技術參數
參數描述
NCP1239D 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low-Standby High Performance PWM Controller
NCP1239F 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:AC-DC Offline Switching Controllers/Regulators
NCP1239FDR2 功能描述:電流型 PWM 控制器 Low Standby Power RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
NCP1239FDR2G 功能描述:電流型 PWM 控制器 Low Standby Power High Performance PWM RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
NCP1239V 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:AC-DC Offline Switching Controllers/Regulators
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*