- 您現(xiàn)在的位置：買賣IC網 > PDF目錄363217 > NCP1239 (ON SEMICONDUCTOR) Low−Standby High Performance PWM Controller PDF資料下載
參數資料
| 型號： | NCP1239 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | Low−Standby High Performance PWM Controller |
| 文件頁數： | 25/38頁 |
| 文件大?。?/td> | 1145K |
| 代理商： | NCP1239 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
NCP1239
http://onsemi.com
25
Pin 3 can serve to build an Overvoltage Protection by
placing a Zener between the voltage to measure (e.g., V
CC
)
and Pin 3 (refer to application schematic). If a 15 V Zener is
applied, the Pin 3 comparator will switch when (V
CC
15 V)
exceeds the 2.4 V internal reference, that is, when V
CC
is
higher than 17.5 V.
This pin can also monitor the temperature using an
external thermistor (refer to application schematic).
Thermistors can be of Negative Temperature Coefficient
(NTC) type (the resistance decreases versus the
temperature) or of Positive Temperature Coefficient (PTC)
type (the resistance increases versus the temperature). Let’s
assume that a NTC thermistor is used (as in the application
schematic). Placing it between the 5 V reference voltage
(REF5V) and Pin 3, and a classical resistance between Pin 3
and ground, the Pin 3 voltage equals:
Vpin3
R
R
Rthermistor
5 V
where R and R
thermistor
are respectively the resistor and the
thermistor resistance.
R
thermistor
decreasing versus the temperature, the Pin 3
voltage (V
pin3
) increases when the temperature grows up.
For instance, the thermistor resistance can be in the range
of 500 k at 25
°
C and as low as 5 k at 130
°
C that as an
example, one can take as the temperature limit the
application must not exceed. Choosing R equal to 5k, the
Pin 3 voltage at 130
°
C that equates:
Vpin3(130
°
C)
5 k
5 k
5 k
5 V
2.5 V
triggers the fault comparator.
This example illustrates that one must just select the
bottom resistor so that it exhibits the same resistance as the
thermistor at the temperature to be detected.
If the thermistor is a PTC, it must be placed between Pin 3
and ground. One must place a resistor between the 5 V
reference voltage and Pin 3. Similarly, the resistor must be
selected so that its resistance equals the thermistor one at the
temperature to be detected.
BrownOut and Over Power Limitation
SMPS are designed for a given input range. When the
input voltage is too low (brownout), the SMPS tends to
compensate by sinking an increased current from the line.
As a result the power components may suffer from an
excessive heating and ultimately the SMPS may be
destroyed. To avoid such a risk, the NCP1239 incorporates
a brownout detection that monitors the portion of the input
voltage that is applied to Pin 5.
Figure 44.
V
pin5
CMP
240 mV 500 mV
An hysteresis comparator monitors the SMPS input voltage
+
Rupper
CMP
HV
Driver is off
as long as
CMP is low
5
+
Driver
Rlower
500 mV if CMP is low
240 mV if CMP is high
Also called “Bulk OK” signal (BOK), the BrownOut
(BO) protection prevents the power supply from being
adversely destroyed in case the mains drops to a very low
value. When it detects such a situation, the NCP1239 no
longer pulses but waits until the bulk voltage goes back to its
normal level. A certain amount of hysteresis needs to be
provided since the bulk capacitor is affected by some ripple,
especially at low input levels. For that reason, when the BO
comparator toggles, the internal reference voltage changes
from 500 mV to 240 mV. This effect is not latched: that is to
say, when the bulk capacitor is below the target, the
controller does not deliver pulses. As soon as the input
voltage growsup and reaches the level imposed by the
resistive divider, pulses are passed to the internal driver and
activate the MOSFET.
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1239FDR2 | Low−Standby High Performance PWM Controller |
| NCP1239FDR2G | Low−Standby High Performance PWM Controller |
| NCP1239VDR2 | Low−Standby High Performance PWM Controller |
| NCP1239VDR2G | Low−Standby High Performance PWM Controller |
| NCP1271 | Soft−Skip Mode Standby PWM Controller with Adjustable Skip Level and External Latch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1239D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low-Standby High Performance PWM Controller |
| NCP1239F | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:AC-DC Offline Switching Controllers/Regulators |
| NCP1239FDR2 | 功能描述:電流型 PWM 控制器 Low Standby Power RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| NCP1239FDR2G | 功能描述:電流型 PWM 控制器 Low Standby Power High Performance PWM RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| NCP1239V | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:AC-DC Offline Switching Controllers/Regulators |
發(fā)布緊急采購，3分鐘左右您將得到回復。