參數資料
型號: NAND512W3A2CZA6E
廠商: 意法半導體
英文描述: 512 Mbit, 528 Byte/264 Word Page, 1.8V/3V, NAND Flash Memories
中文描述: 512兆位,528 Byte/264字的頁面,1.8V/3V,NAND閃存芯片
文件頁數: 6/51頁
文件大?。?/td> 517K
代理商: NAND512W3A2CZA6E
Signal descriptions
NAND512-A2C
14/51
3.7
Write Enable (W)
The Write Enable input, W, controls writing to the Command Interface, Input Address and
Data latches. Both addresses and data are latched on the rising edge of Write Enable.
During power-up and power-down a recovery time of 10s (min) is required before the
Command Interface is ready to accept a command. It is recommended to keep Write Enable
high during the recovery time.
3.8
Write Protect (WP)
The Write Protect pin is an input that gives a hardware protection against unwanted program
or erase operations. When Write Protect is Low, VIL, the device does not accept any
program or erase operations.
It is recommended to keep the Write Protect pin Low, VIL, during power-up and power-down.
3.9
Ready/Busy (RB)
The Ready/Busy output, RB, is an open-drain output that can be used to identify if the P/E/R
Controller is currently active.
When Ready/Busy is Low, VOL, a read, program or erase operation is in progress. When the
operation completes Ready/Busy goes High, VOH.
The use of an open-drain output allows the Ready/Busy pins from several memories to be
connected to a single pull-up resistor. A Low will then indicate that one, or more, of the
memories is busy.
Refer to the Section 10.1: Ready/Busy signal electrical characteristics for details on how to
calculate the value of the pull-up resistor.
3.10
VDD supply voltage
VDD provides the power supply to the internal core of the memory device. It is the main
power supply for all operations (read, program and erase).
An internal voltage detector disables all functions whenever VDD is below the VLKO threshold
(see Section Figure 31.: Data Protection) to protect the device from any involuntary
Program/Erase operations during power-transitions.
Each device in a system should have VDD decoupled with a 0.1F capacitor. The PCB track
widths should be sufficient to carry the required program and erase currents
3.11
VSS ground
Ground, VSS, is the reference for the power supply. It must be connected to the system
ground.
相關PDF資料
PDF描述
NAND512W3A2C 512 Mbit, 528 Byte/264 Word Page, 1.8V/3V, NAND Flash Memories
NAT-3DC-2A+ 1000 MHz - 3500 MHz RF/MICROWAVE FIXED ATTENUATOR
NC26SM-SLF-0.032768MHZ-EZM12510 QUARTZ CRYSTAL RESONATOR, 0.032768 MHz
NCB-CA55SMPGA1 77 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT
NCCA39C-FREQ-OUT23 CRYSTAL OSCILLATOR, CLOCK, 0.25 MHz - 4 MHz, CMOS/TTL OUTPUT
相關代理商/技術參數
參數描述
NAND512W3A2DDI6 制造商:Micron Technology Inc 功能描述:NAND - Gel-pak, waffle pack, wafer, diced wafer on film
NAND512W3A2DN6E 功能描述:IC FLASH 512MBIT 48TSOP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1,000 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:4K (512 x 8) 速度:400kHz 接口:I²C,2 線串口 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC(0.173",4.40mm 寬) 供應商設備封裝:8-MFP 包裝:帶卷 (TR)
NAND512W3A2DZA6E 功能描述:IC FLASH 512MBIT 63VFBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1,000 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:4K (512 x 8) 速度:400kHz 接口:I²C,2 線串口 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC(0.173",4.40mm 寬) 供應商設備封裝:8-MFP 包裝:帶卷 (TR)
NAND512W3A2SE06 制造商:Micron Technology Inc 功能描述:NAND - Gel-pak, waffle pack, wafer, diced wafer on film
NAND512W3A2SN6E 功能描述:IC FLASH 512MBIT 48TSOP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1 系列:- 格式 - 存儲器:閃存 存儲器類型:閃存 - NAND 存儲容量:4G(256M x 16) 速度:- 接口:并聯 電源電壓:2.7 V ~ 3.6 V 工作溫度:0°C ~ 70°C 封裝/外殼:48-TFSOP(0.724",18.40mm 寬) 供應商設備封裝:48-TSOP I 包裝:Digi-Reel® 其它名稱:557-1461-6