參數資料
型號: NAND512W3A2C
廠商: 意法半導體
英文描述: 512 Mbit, 528 Byte/264 Word Page, 1.8V/3V, NAND Flash Memories
中文描述: 512兆位,528 Byte/264字的頁面,1.8V/3V,NAND閃存芯片
文件頁數: 6/51頁
文件大小: 517K
代理商: NAND512W3A2C
Signal descriptions
NAND512-A2C
14/51
3.7
Write Enable (W)
The Write Enable input, W, controls writing to the Command Interface, Input Address and
Data latches. Both addresses and data are latched on the rising edge of Write Enable.
During power-up and power-down a recovery time of 10s (min) is required before the
Command Interface is ready to accept a command. It is recommended to keep Write Enable
high during the recovery time.
3.8
Write Protect (WP)
The Write Protect pin is an input that gives a hardware protection against unwanted program
or erase operations. When Write Protect is Low, VIL, the device does not accept any
program or erase operations.
It is recommended to keep the Write Protect pin Low, VIL, during power-up and power-down.
3.9
Ready/Busy (RB)
The Ready/Busy output, RB, is an open-drain output that can be used to identify if the P/E/R
Controller is currently active.
When Ready/Busy is Low, VOL, a read, program or erase operation is in progress. When the
operation completes Ready/Busy goes High, VOH.
The use of an open-drain output allows the Ready/Busy pins from several memories to be
connected to a single pull-up resistor. A Low will then indicate that one, or more, of the
memories is busy.
Refer to the Section 10.1: Ready/Busy signal electrical characteristics for details on how to
calculate the value of the pull-up resistor.
3.10
VDD supply voltage
VDD provides the power supply to the internal core of the memory device. It is the main
power supply for all operations (read, program and erase).
An internal voltage detector disables all functions whenever VDD is below the VLKO threshold
(see Section Figure 31.: Data Protection) to protect the device from any involuntary
Program/Erase operations during power-transitions.
Each device in a system should have VDD decoupled with a 0.1F capacitor. The PCB track
widths should be sufficient to carry the required program and erase currents
3.11
VSS ground
Ground, VSS, is the reference for the power supply. It must be connected to the system
ground.
相關PDF資料
PDF描述
NAT-3DC-2A+ 1000 MHz - 3500 MHz RF/MICROWAVE FIXED ATTENUATOR
NC26SM-SLF-0.032768MHZ-EZM12510 QUARTZ CRYSTAL RESONATOR, 0.032768 MHz
NCB-CA55SMPGA1 77 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT
NCCA39C-FREQ-OUT23 CRYSTAL OSCILLATOR, CLOCK, 0.25 MHz - 4 MHz, CMOS/TTL OUTPUT
NCCA39B-FREQ-OUT23 CRYSTAL OSCILLATOR, CLOCK, 0.25 MHz - 4 MHz, CMOS/TTL OUTPUT
相關代理商/技術參數
參數描述
NAND512W3A2CE06 功能描述:閃存 NAND & S.MEDIA FLASH RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
NAND512W3A2CN6E 功能描述:閃存 512 MBIT MEM ARRAY NAND FLASH MEMORY RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
NAND512W3A2CN6F 功能描述:閃存 512 MB 528 Byte 264 word pg 1.8V/3V RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
NAND512W3A2CZA6E 功能描述:IC FLASH 512MBIT 63VFBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 產品變化通告:Product Discontinuation 26/Apr/2010 標準包裝:136 系列:- 格式 - 存儲器:RAM 存儲器類型:SRAM - 同步,DDR II 存儲容量:18M(1M x 18) 速度:200MHz 接口:并聯 電源電壓:1.7 V ~ 1.9 V 工作溫度:0°C ~ 70°C 封裝/外殼:165-TBGA 供應商設備封裝:165-CABGA(13x15) 包裝:托盤 其它名稱:71P71804S200BQ
NAND512W3A2DDI6 制造商:Micron Technology Inc 功能描述:NAND - Gel-pak, waffle pack, wafer, diced wafer on film