參數資料
型號： NAND512R4A2C
廠商： 意法半導體
英文描述： 512 Mbit, 528 Byte/264 Word Page, 1.8V/3V, NAND Flash Memories
中文描述： 512兆位，528 Byte/264字的頁面，1.8V/3V，NAND閃存芯片
文件頁數： 18/51頁
文件大?。?/td> 517K
代理商： NAND512R4A2C
NAND512-A2C
Device operations
25/51
6.5
Block Erase
Erase operations are done one block at a time. An erase operation sets all of the bits in the
addressed block to ‘1’. All previous data in the block is lost.
An erase operation consists of three steps (refer to Figure 12):
1.
One bus cycle is required to setup the Block Erase command.
2.
Only three bus cycles for 512Mb and 1Gb devices, or two for 128Mb and 256Mb
devices are required to input the block address. The first cycle (A0 to A7) is not
required as only addresses A14 to A25 are valid, A9 to A13 are ignored. In the last
address cycle I/O2 to I/O7 must be set to VIL.
3.
One bus cycle is required to issue the confirm command to start the P/E/R Controller.
Once the erase operation has completed the Status Register can be checked for errors.
Figure 12.
Block Erase operation
6.6
Reset
The Reset command is used to reset the Command Interface and Status Register. If the
Reset command is issued during any operation, the operation will be aborted. If it was a
program or erase operation that was aborted, the contents of the memory locations being
modified will no longer be valid as the data will be partially programmed or erased.
If the device has already been reset then the new Reset command will not be accepted.
The Ready/Busy signal goes Low for tBLBH4 after the Reset command is issued. The value
of tBLBH4 depends on the operation that the device was performing when the command was
issued, refer to Table 21 for the values.
I/O
RB
Block Address
Inputs
SR0
ai07593
D0h
70h
60h
Block Erase
Setup Code
Confirm
Code
Read Status Register
Busy
tBLBH3
(Erase Busy time)
相關PDF資料
PDF描述
NAND512W3A2CZA6E 512 Mbit, 528 Byte/264 Word Page, 1.8V/3V, NAND Flash Memories
NAND512W3A2C 512 Mbit, 528 Byte/264 Word Page, 1.8V/3V, NAND Flash Memories
NAT-3DC-2A+ 1000 MHz - 3500 MHz RF/MICROWAVE FIXED ATTENUATOR
NC26SM-SLF-0.032768MHZ-EZM12510 QUARTZ CRYSTAL RESONATOR, 0.032768 MHz
NCB-CA55SMPGA1 77 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT
相關代理商/技術參數
參數描述
NAND512R4A2CWFD 制造商:Micron Technology Inc 功能描述:NAND - Gel-pak, waffle pack, wafer, diced wafer on film
NAND512R4A2CZA6 制造商:Micron Technology Inc 功能描述:512MB. 3V X8 NO OPTION TSOP48TSOP-1 48 12X20 AL 42 - Trays
NAND512R4A2DDI6 制造商:Micron Technology Inc 功能描述:NAND - Gel-pak, waffle pack, wafer, diced wafer on film
NAND512W3A0AN6 功能描述:閃存 NAND & S.MEDIA FLASH RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
NAND512W3A0AN6E 功能描述:閃存 2.7-3.6V 512M(64Mx8) RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*