- 您現在的位置：買賣IC網 > PDF目錄188955 > MX53L06402L-50 (MACRONIX INTERNATIONAL CO LTD) FLASH 2.7V PROM CARD, XMA7 PDF資料下載
參數資料
| 型號： | MX53L06402L-50 |
| 廠商： | MACRONIX INTERNATIONAL CO LTD |
| 元件分類： | PROM |
| 英文描述： | FLASH 2.7V PROM CARD, XMA7 |
| 封裝： | CRAD-7 |
| 文件頁數： | 9/55頁 |
| 文件大?。?/td> | 262K |
| 代理商： | MX53L06402L-50 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
17
P/N: PM1043
REV. 1.0, NOV. 25, 2003
MX53L06402
Figure 5: MX53L06402 state diagram (data transfer mode)
The command SELECT_DESELECT_CARD (CMD7) is used to select one card and place it in the Transfer State. If
a previously selected card is in the Transfer State its connection with the host is released and it will move back to the
Stand-by State. Only one card can be, at any time, in the Transfer State. A selected card is responding the CMD7,
the deselected one does not respond to this command.
When CMD7 is sent including the reserved relative card address "0x0000", all cards transfer back to Stand-by State.
This command is used to identify new cards without resetting other already acquired cards. Cards to which an RCA
has already been assigned, do not respond to the identification command flow in this state.
All the data communication in the Data Transfer Mode is consequently a point-to point communication between the
host and the selected card (using addressed commands). All addressed commands are acknowledged by a response
on the CMD line.
All read commands (data is sent from the card via data lines) can be interrupted at any time, by another read or a stop
command.
The DAT bus line is high when no data is transmitted. A transmitted data block consists of a start bit (LOW), followed
by a continuous data stream. The data stream contains the net payload data (and error correction bits if an off-card
ECC is used). The data stream ends with an end bit (HIGH). The data transmission is synchronous to the clock signal.
The payload for block oriented data transfer is protected by a CRC check sum (see "Chapter 7:Error handling").
Stand-by State
(stby)
Sending-data
State
Transfer
State(tran)
CMD7
CMD4,
9,10
CMD7
card is not addressed
card is addressed
CMD3
card identification mode
data transfer mode
no state transition
in data-transfer-mode
CMD13
CMD15
from all states in
data-transfer-mode
CMD0
CMD16,23
CMD11, 17, 18
CMD12
"operation
complete"
相關PDF資料 |
PDF描述 |
|---|---|
| MX574AKCWI-T | Industry-Standard, 12-Bit ADC with Reference |
| MX574AKEQI-T | Industry-Standard, 12-Bit ADC with Reference |
| MX574AKP-T | Industry-Standard, 12-Bit ADC with Reference |
| MX574ALCWI-T | Industry-Standard, 12-Bit ADC with Reference |
| MX574ALP-T | Industry-Standard, 12-Bit ADC with Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MX54-3 | 功能描述:CUTTER SIDE OVAL FLUSH 4.25" RoHS:是 類別:工具 >> 切割機 系列:STUSA 標準包裝:1 系列:Xcelite® 類型:側面（對角） 形狀:錐形 切邊:凹槽 長度 - 總體:5.00"（127mm） 特點:安全夾 容量:20 AWG 軟線 重量:0.2 磅（90.72g） |
| MX-543/U | 制造商:Kings Electronics 功能描述: |
| MX54-9 | 功能描述:CUTTER SIDE OVAL FLUSH 4.25" RoHS:是 類別:工具 >> 切割機 系列:STUSA 標準包裝:1 系列:Xcelite® 類型:側面（對角） 形狀:錐形 切邊:凹槽 長度 - 總體:5.00"（127mm） 特點:安全夾 容量:20 AWG 軟線 重量:0.2 磅（90.72g） |
| MX54S30J | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MX-550-PSU | 制造商:Maxxtro 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。