- 您現在的位置：買賣IC網 > PDF目錄359234 > MT90520AG (ZARLINK SEMICONDUCTOR INC) 8-Port Primary Rate Circuit Emulation AAL1 SAR PDF資料下載
參數資料
| 型號： | MT90520AG |
| 廠商： | ZARLINK SEMICONDUCTOR INC |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | 8-Port Primary Rate Circuit Emulation AAL1 SAR |
| 中文描述： | ATM SEGMENTATION AND REASSEMBLY DEVICE, PBGA456 |
| 封裝： | 35 X 35 MM, 1.27 MM PITCH, PLASTIC, MS-034, BGA-456 |
| 文件頁數： | 99/180頁 |
| 文件大?。?/td> | 1736K |
| 代理商： | MT90520AG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁當前第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁
MT90520
Data Sheet
99
Zarlink Semiconductor Inc.
4.7.2.4 Transmit SRTS Circuit Sub-module
In the segmentation direction, the purpose of the transmit SRTS circuit sub-module is to generate 4-bit Residual
Time Stamps (RTSs) to be inserted within the headers of ATM cells output on the UTOPIA bus. In the reassembly
direction, this circuit is used to generate local RTS values which are compared (by an internal PLL) with the RTS
values extracted from received cells. Segmentation operation is explained in this section, but the reassembly
function is discussed in Section 4.7.2.5, “Receive SRTS Circuit Sub-Module”.
As outlined in U.S. Patent No. 5,260,978, in the segmentation direction, the transmit SRTS circuit compares the
local clock rate, determined by STiCLK for a particular port (in independent clocking or ST-BUS backplane mode) or
C4M/C2M (when operating in Generic backplane mode) with the output of an fnxi counter clocked by the Network
Clock Divider circuit examined in Section 4.7.2.3 on page 97. The result of the comparison is stored in a FIFO, for
eventual transmission of the RTS nibbles to the TX_SAR. Underrun and overflow detection are provided on the
Transmit SRTS FIFO via status bits in CPU-accessible registers. The circuit operates in essentially the same way in
the reassembly direction, except that the local clock rate is determined by the clock at the output of the port’s
internal PLL, PLLCLK. As well, in the reassembly direction, data is sent to the Receive SRTS sub-module rather
than being sent to the Transmit SRTS FIFO. Figure 39 shows how the circuit is implemented.
Figure 39 - Transmit SRTS Sub-module
UDT Operation
The STiCLK or PLLCLK signal for each port (C4M/C2M isn’t used, because it is an SDT-mode signal) is divided
down to generate a clock, RTS_CLK. This clock has the same frequency as a cycle of RTS. Since one RTS value is
transmitted over the course of 8 cells, the division is by 3008, the number of payload bits transmitted within one
RTS period (8 cells containing 47 payload bytes). Every time RTS_CLK pulses, the current value of the appropriate
fnxi counter is stored in a FIFO. A value from the FIFO is transmitted to the TX_SAR cell header generator circuit
once every 8-cell sequence.
Clock Management Module
Divider
Circuitry
(/ 3008 or
/ 3000)
5-deep 4-bit
FIFO
Note 1:
The 4-bit fnxi counters are only required once per device. All the other circuitry is instantiated on a per-port basis.
4
4
Gapping
Circuitry
(see
Figure 40)
SDT/UDT
TX_SAR
Module
fnxi counters
(generated by
Network Clock
Divider Circuit
)
STiCLK
New FIFO Entry
PLLCLK
RTSSEL
Transmit RTS
Value
2:1
Mux
Mux
2:1
Mux
C4M/C2M
fnxi1_count<3:0>
fnxi2_count<3:0>
FNXISEL
RTS_CLK
sync_clk
To port’s PLL for RX
SRTS Recovery
RTS_int<3:0>
SDT/UDT
Note 2:
PLLCLK is used when receiving RTS (clock recovery) or to dejitter the clock before generating RTS.
相關PDF資料 |
PDF描述 |
|---|---|
| MT9072 | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| MT9072AB | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| MT9072AV | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| MT90820 | Large Digital Switch |
| MT90820AL | Large Digital Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT90520AG2 | 制造商:Microsemi Corporation 功能描述:ATM SAR 2.048MBPS 2.5V CBR 456BGA - Trays 制造商:Zarlink Semiconductor Inc 功能描述:ATM SAR 2.048MBPS 2.5V CBR 456BGA - Trays |
| MT90528 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:28-Port Primary Rate Circuit Emulation AAL1 SAR |
| MT90528AG | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:28-Port Primary Rate Circuit Emulation AAL1 SAR |
| MT90528AG2 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:28-Port Primary Rate Circuit Emulation AAL1 SAR |
| MT90710 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:High-Speed Isochronous Multiplexer |
發布緊急采購，3分鐘左右您將得到回復。