- 您現在的位置：買賣IC網 > PDF目錄359234 > MT9040 (Zarlink Semiconductor Inc.) T1/E1 Synchronizer PDF資料下載
參數資料
| 型號： | MT9040 |
| 廠商： | Zarlink Semiconductor Inc. |
| 英文描述： | T1/E1 Synchronizer |
| 中文描述： | 的T1/E1同步 |
| 文件頁數： | 4/27頁 |
| 文件大?。?/td> | 424K |
| 代理商： | MT9040 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
MT9040
Data Sheet
4
Zarlink Semiconductor Inc.
Functional Description
The MT9040 is a T1/E1 Trunk Synchronizer, providing timing (clock) and synchronization (frame) signals to
interface circuits for T1 and E1 Primary Rate Digital Transmission links. Figure 1 is a functional block diagram which
is described in the following sections.
Frequency Select MUX Circuit
The MT9040 operates on the falling edge of the reference. It operates with one of four possible input reference
frequencies (8kHz, 1.544MHz, 2.048MHz or 19.44MHz). The frequency select inputs (FS1 and FS2) determine
which of the four frequencies may be used at the reference input. A reset (RST) must be performed after every
frequency select input change. See Table 1.
Table 1 - Input Frequency Selection
Digital Phase Lock Loop (DPLL)
As shown in Figure 3, the DPLL of the MT9040 consists of a Phase Detector, Loop Filter, Digitally Controlled
Oscillator and a Control Circuit.
Phase Detector
- the Phase Detector compares the reference signal with the feedback signal from the Frequency
Select MUX circuit, and provides an error signal corresponding to the phase difference between the two. This error
signal is passed to the Loop Filter. The Frequency Select MUX allows the proper feedback signal to be externally
selected (e.g., 8kHz, 1.544MHz, 2.048MHz or 19.44MHz).
45
TDI
Test Serial Data In (Input).
JTAG serial test instructions and data are shifted in on this pin.
This pin is internally pulled up to V
DD
.
Test Reset (Input).
Asynchronously initializes the JTAG TAP controller by putting it in the
Test-Logic-Reset state. If not used, this pin should be held low.
46
TRST
47
TCK
Test Clock (Input).
Provides the clock to the JTAG test logic.
48
TMS
Test Mode Select (Input).
JTAG signal that controls the state transitions of the TAP controller.
FS2
FS1
Input Frequency
0
0
19.44MHz
0
1
8kHz
1
0
1.544MHz
1
1
2.048MHz
Pin Description (continued)
Pin #
Name
Description
相關PDF資料 |
PDF描述 |
|---|---|
| MT9040AN | T1/E1 Synchronizer |
| MT9043 | T1/E1 System Synchronizer |
| MT9043AN | T1/E1 System Synchronizer |
| MT9043AN48PINSSOP | T1/E1 System Synchronizer |
| MT9045 | T1/E1/OC3 System Synchronizer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT90401 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:SONET/SDH Clock Multiplier PLL |
| MT90401AB | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:SONET/SDH System Synchronizer |
| MT90401AB1 | 制造商:Microsemi Corporation 功能描述:FRAMER SDH/SONET 3.3V 80LQFP EP - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC SYNCHRONIZER SONET/SDH 80LQFP 制造商:Microsemi Corporation 功能描述:IC SYNCHRONIZER SONET/SDH 80LQFP |
| MT9040AN | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1 Synchronizer |
| MT9040AN1 | 制造商:Microsemi Corporation 功能描述:FRAMER E1 /T1 3.3V 48SSOP - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。