參數資料
型號： MT8920BP
廠商： Mitel Networks Corporation
英文描述： ISO-CMOS ST-BUS⑩ FAMILY ST-BUS Parallel Access Circuit
中文描述： 異意法半導體的CMOS總線⑩家庭圣總線并行訪問電路
文件頁數： 2/24頁
文件大?。?/td> 534K
代理商： MT8920BP
MT8920B
CMOS
3-4
Figure 2 - Pin Connections
Pin Description
Pin #
Name
Description
1
C4i
4.096 MHz Clock.
The ST-BUS timing clock used to establish bit cell boundaries for the serial
bus.
2
F0i
Framing Pulse.
A low going pulse used to synchronize the STPA to the 2048 kbit/s ST-BUS
stream. The first falling edge of C4i subsequent to the falling edge of F0i identifies the start of
a frame.
3
IACK
Interrupt Acknowledge (Mode 1).
This active low input signals that the current bus cycle is
an interrupt vector fetch cycle. Upon receiving this acknowledgement, the STPA will
output a user-programmed vector number on D
0
- D
7
indicating the source of the interrupt.
Mode Select 1 (Mode 2,3).
This input is used to select the device operating modes. A low
applied to this pin will select mode 3 while a high will select mode 2. (Refer to Table 1.)
MS1
4
STi0
ST-BUS Input 0.
This is the input for the 2048 kbit/s ST-BUS serial data stream.
5
CS
Chip Select.
This active low input is used to select the STPA for a parallel access .
6
DS
Data Strobe (Mode 1).
This active low input indicates to the STPA that valid data is on the data
bus during a write operation or that the STPA must output valid data on the data bus during a
read operation.
OE
Output Enable (Mode 2).
This active low input enables the data bus driver outputs.
OE
Output Enable (Mode 3).
This active low output indicates that the selected device is to be
read and that the data bus is available for data transfer.
7
R/W
Read/Write (Mode 1,2).
This input defines the data bus transfer as a read (R/W = 1) or a write
(R/W= 0) cycle.
WE
Write Enable (Mode 3).
This active low output indicates the data on the data bus is to be
written into the selected location of an external device.
8-12
A0-A4
Address Bus (Mode 1,2).
These inputs are used to select the internal registers and two-port
memories of the STPA.
A0-A4
Address Bus (Mode 3).
These address outputs are generated by the STPA and reflect the
position in internal RAM where the information will be fetched from or stored in. Addresses
generated in this mode are used to access external devices for direct memory transfer.
28 PIN J-LEAD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
28
27
26
25
24
23
22
21
C4i
F0i
IACK, MS1
STi0
CS
DS, OE
R/W, WE
A0
A1
A2
A3
A4
A5, STCH
VSS
VDD
MMS
DTACK, BUSY, DCS
IRQ, 24/32
STo1
STo0
D7
D6
D5
D4
D3
D2
D1
D0
28 PIN PDIP/CERDIP/SOIC
2
4
3
2
1
2
2
5
6
7
8
9
10
11
25
24
23
22
21
20
19
1
1
1
1
1
1
1
F
I
S
C
V
M
D
IRQ, 24/32
STo1
STo0
D7
D6
D5
D4
CS
DS, OE
R/W, WE
A0
A1
A2
A3
A
V
D
D
D
D
B
A
相關PDF資料
PDF描述
MT8920BS ISO-CMOS ST-BUS⑩ FAMILY ST-BUS Parallel Access Circuit
MT8926 ISO-CMOS ST-BUS⑩ FAMILY T1 Performance Monitoring Adjunct Circuit (PMAC)
MT8926AE ISO-CMOS ST-BUS⑩ FAMILY T1 Performance Monitoring Adjunct Circuit (PMAC)
MT8926AP ISO-CMOS ST-BUS⑩ FAMILY T1 Performance Monitoring Adjunct Circuit (PMAC)
MT8930B Subscriber Network Interface Circuit
相關代理商/技術參數
參數描述
MT8920BP1 制造商:Microsemi Corporation 功能描述:ST-BUS PARALLEL ACCESS CIRCUIT 28PLCC - Rail/Tube 制造商:Zarlink Semiconductor Inc 功能描述:ST-BUS PARALLEL ACCESS CIRCUIT 28PLCC - Rail/Tube
MT8920BPR1 制造商:Microsemi Corporation 功能描述:ST-BUS PARALLEL ACCESS CIRCUIT 28PLCC - Tape and Reel 制造商:Zarlink Semiconductor Inc 功能描述:ST-BUS PARALLEL ACCESS CIRCUIT 28PLCC - Tape and Reel
MT8920BS 制造商:Microsemi Corporation 功能描述:
MT8920BS1 制造商:Microsemi Corporation 功能描述:ST-BUS PARALLEL ACCESS CIRCUIT 28SOIC - Rail/Tube 制造商:Zarlink Semiconductor Inc 功能描述:ST-BUS PARALLEL ACCESS CIRCUIT 28SOIC - Rail/Tube
MT8924 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:PCM Conference Circuit (PCC) Preliminary Information
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*