參數資料
型號： MT48H8M16LFB4-8IT:JTR
元件分類： DRAM
英文描述： 8M X 16 SYNCHRONOUS DRAM, 6 ns, PBGA54
封裝： 8 X 8 MM, LEAD FREE, VFBGA-54
文件頁數： 9/61頁
文件大?。?/td> 2469K
PDF: 09005aef8237e877/Source: 09005aef8237e8d8
Micron Technology, Inc., reserves the right to change products or specifications without notice.
128Mb_x16 Mobile SDRAM_Y25M_2.fm - Rev. A 6/06 EN
17
2006 Micron Technology, Inc. All rights reserved.
128Mb: x16 Mobile SDRAM
BURST TERMINATE
Preliminary
PRECHARGE
The PRECHARGE command is used to deactivate the open row in a particular bank or
the open row in all banks. The bank(s) will be available for a subsequent row access a
specified time (tRP) after the PRECHARGE command is issued. Input A10 determines
whether one or all banks are to be precharged, and in the case where only 1 bank is to be
precharged, inputs BA0, BA1 select the bank. Otherwise BA0, BA1 are treated as “Don’t
Care.” Once a bank has been precharged, it is in the idle state and must be activated
prior to any READ or WRITE commands being issued to that bank.
Auto Precharge
Auto precharge is a feature which performs the same individual-bank precharge func-
tion described above, without requiring an explicit command. This is accomplished by
using A10 to enable auto precharge in conjunction with a specific READ or WRITE
command. A precharge of the bank/row that is addressed with the READ or WRITE
command is automatically performed upon completion of the READ or WRITE burst.
Auto precharge is non persistent because it is either enabled or disabled for each indi-
vidual READ or WRITE command.
Auto precharge ensures that the precharge is initiated at the earliest valid stage within a
burst. The user must not issue another command to the same bank until the precharge
time (tRP) is completed. This is determined as if an explicit PRECHARGE command was
issued at the earliest possible time, as described for each burst type in "Operation" on
BURST TERMINATE
The BURST TERMINATE command is used to truncate fixed-length bursts. The most
recently registered READ or WRITE command prior to the BURST TERMINATE
command will be truncated, as shown in "Operation" on page 18.
AUTO REFRESH
AUTO REFRESH is used during normal operation of the SDRAM and is analogous to
CAS#-BEFORE-RAS# (CBR) refresh in conventional DRAMs. This command is nonper-
sistent, so it must be issued each time a refresh is required. All active banks must be
PRECHARGED prior to issuing an AUTO REFRESH command. The AUTO REFRESH
command should not be issued until the minimum tRP has been met after the
PRECHARGE command as shown in "Operation" on page 18.
The addressing is generated by the internal refresh controller. This makes the address
bits “Don’t Care” during an AUTO REFRESH command. The 128Mb SDRAM requires
4,096 AUTO REFRESH cycles every 64ms (tREF). Providing a distributed AUTO REFRESH
command every 15.625s will meet the refresh requirement and ensure that each row is
refreshed. Alternatively, 4,096 AUTO REFRESH commands can be issued in a burst at the
minimum cycle rate (tRFC), once every 64ms.
SELF REFRESH
The SELF REFRESH command can be used to retain data in the SDRAM, even if the rest
of the system is powered down, as long as power is not completely removed from the
SDRAM. When in the self refresh mode, the SDRAM retains data without external
clocking. The SELF REFRESH command is initiated like an AUTO REFRESH command
相關PDF資料
PDF描述
MT48LC4M32TG-10 4M X 32 SYNCHRONOUS DRAM, 7 ns, PDSO54
MT48V8M16LFB4-8XT 8M X 16 SYNCHRONOUS DRAM, 7 ns, PBGA54
MT48LC4M32LFB5-10ES:G 4M X 32 SYNCHRONOUS DRAM, 7 ns, PBGA90
MT48V4M32TG-8XT 4M X 32 SYNCHRONOUS DRAM, 7 ns, PDSO54
MT48LC8M8A2TG-8EL:GIT 8M X 8 SYNCHRONOUS DRAM, 6 ns, PDSO54
相關代理商/技術參數
參數描述
MT48H8M16LFF3-7E 制造商:Micron Technology Inc 功能描述:
MT48H8M16LFF4-10 功能描述:IC SDRAM 128MBIT 100MHZ 54VFBGA RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1 系列:- 格式 - 存儲器:RAM 存儲器類型:SDRAM 存儲容量:256M（8Mx32） 速度:143MHz 接口:并聯 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:90-VFBGA 供應商設備封裝:90-VFBGA（8x13） 包裝:托盤 其它名稱:Q2841869
MT48H8M16LFF4-10 IT 功能描述:IC SDRAM 128MBIT 100MHZ 54VFBGA RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1 系列:- 格式 - 存儲器:RAM 存儲器類型:SDRAM 存儲容量:256M（8Mx32） 速度:143MHz 接口:并聯 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:90-VFBGA 供應商設備封裝:90-VFBGA（8x13） 包裝:托盤 其它名稱:Q2841869
MT48H8M16LFF4-8 功能描述:IC SDRAM 128MBIT 125MHZ 54VFBGA RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1 系列:- 格式 - 存儲器:RAM 存儲器類型:SDRAM 存儲容量:256M（8Mx32） 速度:143MHz 接口:并聯 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:90-VFBGA 供應商設備封裝:90-VFBGA（8x13） 包裝:托盤 其它名稱:Q2841869
MT48H8M16LFF4-8 IT 功能描述:IC SDRAM 128MBIT 125MHZ 54VFBGA RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1 系列:- 格式 - 存儲器:RAM 存儲器類型:SDRAM 存儲容量:256M（8Mx32） 速度:143MHz 接口:并聯 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:90-VFBGA 供應商設備封裝:90-VFBGA（8x13） 包裝:托盤 其它名稱:Q2841869
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*