- 您現在的位置：買賣IC網 > PDF目錄11649 > MCZ33793EFR2 (Freescale Semiconductor)IC DSI SLAVE FOR R-SENSE 16-SOIC PDF資料下載
參數資料
| 型號： | MCZ33793EFR2 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 11/27頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DSI SLAVE FOR R-SENSE 16-SOIC |
| 標準包裝： | 1 |
| 類型： | 傳感器接口 |
| 輸入類型： | 邏輯 |
| 輸出類型： | 邏輯 |
| 接口： | 并聯 |
| 電流 - 電源： | 250mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SOIC N |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 808 (CN2011-ZH PDF) |
| 其它名稱： | MCZ33793EFR2DKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
33793
FUNCTIONAL DEVICE OPERATION
DSI COMMANDS AND RESPONSES
Reads and writes are long-word commands only. The
command format is found in Table 21.
READ/WRITE NVM RESPONSE
This response message is sent during the next message
following a valid Read/Write NVM command to the addressed
device. The response format is found in Table 22. The high
byte is omitted during the short-word response. No response
is generated if the command address field was $0.
CLEAR LOGIC OUT COMMAND
The Clear Logic Out command sets the Logic Out pin to a
logic low. The compliment to this command is the Set Logic
Out. The Logic Out is also cleared at power-up or following a
Clear command. The format of the Clear Logic Out command
is shown in Table 23.
CLEAR LOGIC OUT RESPONSE
This response message is sent during the next message
following a valid Clear Logic Out command to the addressed
device. The response is shown in Table 24. No response is
generated if the command address field was $0.
Table 21. Read/Write NVM Command Format
Data
Address
Command
CRC
1
PA3
PA2
PA1
PA0
A3
A2
A1
A0
1
0
1
X3
X2
X1
X0
Legend
A[3:0] = Address bits. These bits are the address of the device
previously sent with the Initialization command. They must match
the address in the PA[3:0] field and the address stored in the device
address register.
PA[3:0] = Program Address bits. These bits are the address that is to be
programmed into the slave.
X[3:0] = Cyclic Redundancy Check (CRC). The CRC as calculated by the
master.
Table 22. Read/Write NVM Response Format
High Byte
Low Byte
CRC
A3
A2
A1
A0
0
1
PA3
PA2
PA1
PA0
X3
X2
X1
X0
Legend
A[3:0] = Address bits. The slave address.
PA[3:0] = Programmed Address bits. The address that was
programmed into the NVM address bits of the slave.
X[3:0] = Cyclic Redundancy Check (CRC). The CRC as calculated by the
slave.
Table 23. Clear Logic Out Command Format
Data
Address
Command
CRC
–
–-
A3
A2
A1
A0
1
0
X3
X2
X1
X0
Legend
A[3:0] = Address bits. The address of the selected device.
X[3:0] = Cyclic Redundancy Check (CRC). The CRC as calculated by the
master.
Table 24. Clear Logic Out Response Format
High Byte
Low Byte
CRC
A3
A2
A1
A0
0
NV
U
LO
BS
IO3
IO2
IO1
IO0
X3
X2
X1
X0
Legend
A[3:0] = Address bits. The slave address.
BS = Bus Switch Position (1=closed).
LO = Logic out driven level.
IO[3:0] = Values at logic I/Os.
NV = Nonvolatile Memory Write. The value of the NV bit in the slave.
U = Undervoltage indicated true by a “1”.
X[3:0] = Cyclic Redundancy Check (CRC). The CRC as calculated by the
slave.
相關PDF資料 |
PDF描述 |
|---|---|
| CS4121EDWFR20G | IC TACH/SPEEDO DRIVER 20-SOIC |
| CS4121EDWFR20 | IC TACH/SPEEDO DRIVER 20-SOIC |
| CS4121EDWF20G | IC TACH/SPEEDO DRIVER 20-SOIC |
| CS4121EDWF20 | IC TACH/SPEEDO DRIVER 20-SOIC |
| 415484-1 | CONN SMB PLUG RG179 R/A CRIMP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33797EK | 功能描述:功率驅動器IC FOUR CHANNEL SQUIB DR RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MCZ33797EKR2 | 功能描述:功率驅動器IC FOUR CHANNEL SQUIB DR RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MCZ33800EK | 功能描述:馬達/運動/點火控制器和驅動器 AUTO ENG Control IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33800EKR2 | 功能描述:馬達/運動/點火控制器和驅動器 AUTO ENG CONTROL IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33800R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Engine Control Integrated Circuit |
發(fā)布緊急采購，3分鐘左右您將得到回復。