- 您現在的位置：買賣IC網 > PDF目錄383594 > MCP6241 (Microchip Technology Inc.) 50 uA, 650 kHz Rail-to-Rail Op Amp PDF資料下載
參數資料
| 型號： | MCP6241 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 50 uA, 650 kHz Rail-to-Rail Op Amp |
| 中文描述： | 50微安，650千赫軌至軌運算放大器 |
| 文件頁數： | 7/20頁 |
| 文件大?。?/td> | 268K |
| 代理商： | MCP6241 |
2004 Microchip Technology Inc.
DS21882B-page 7
MCP6241/2
3.0
APPLICATION INFORMATION
The MCP6241/2 family of op amps is manufactured
using Microchip’s state-of-the-art CMOS process and
is specifically designed for low-power and general-
purpose applications. The low supply voltage, low
quiescent current and wide bandwidth makes the
MCP6241/2 ideal for battery-powered applications.
3.1
Rail-to-Rail Input
The MCP6241/2 op amps are designed to prevent
phase reversal when the input pins exceed the supply
voltages. Figure 3-1 shows the input voltage exceeding
the supply voltage without any phase reversal.
FIGURE 3-1:
Phase Reversal.
The MCP6241/2 Show No
The input stage of the MCP6241/2 op amps use two
differential input stages in parallel. One operates at low
common mode input voltage (V
CM
) and the other at
high V
CM
. With this topology, the device operates with
V
CM
up to 300 mV above V
DD
and 300 mV below V
SS
.
The
Input
Offset
Voltage
V
CM
= V
SS
– 300 mV and V
DD
+ 300 mV to ensure
proper operation.
Input voltages that exceed the input voltage range
(V
SS
– 0.3V to V
DD
+ 0.3V at 25°C) can cause
excessive current to flow into or out of the input pins.
Current beyond ±2 mA can cause reliability problems.
Applications that exceed this rating must be externally
limited with a resistor, as shown in Figure 3-2.
is
measured
at
FIGURE 3-2:
Resistor (R
IN
).
Input Current-Limiting
3.2
Rail-to-Rail Output
The output voltage range of the MCP6241/2 op amps
is V
DD
– 35 mV (min.) and V
SS
+ 35 mV (max.) when
R
L
= 100 k
is connected to V
DD
/2 and V
DD
= 5.5V.
Refer to Figure 2-14 for more information.
3.3
Capacitive Loads
Driving large capacitive loads can cause stability
problems for voltage feedback op amps. As the load
capacitance increases, the feedback loop’s phase
margin decreases and the closed-loop bandwidth is
reduced. This produces gain peaking in the frequency
response, with overshoot and ringing in the step
response. A unity-gain buffer (G = +1) is the most
sensitive to capacitive loads, but all gains show the
same general behavior.
When driving large capacitive loads with these op
amps (e.g., > 100 pF when G = +1), a small series
resistor at the output (R
ISO
in Figure 3-3) improves the
feedback loop’s phase margin (stability) by making the
output load resistive at higher frequencies. It does not,
however, improve the bandwidth.
FIGURE 3-3:
stabilizes large capacitive loads.
Output resistor, R
ISO
Figure 3-4 gives recommended R
ISO
values for
different capacitive loads and gains. The x-axis is the
normalized load capacitance (C
L
/G
N
), where G
N
is the
circuit’s noise gain. For non-inverting gains, G
N
and the
gain are equal. For inverting gains, G
N
is 1 + |Gain|
(e.g., –1 V/V gives G
N
= +2 V/V).
-1
0
1
2
3
4
5
6
0.E+00
1.E+00
2.E+00
3.E+00
4.E+00
5.E+00
6.E+00
7.E+00
8.E+00
9.E+00
1.E+01
Time (1 ms/div)
I
V
DD
= 5.0V
G = +2 V/V
V
IN
V
OUT
R
IN
V
---------–
Minimum expected V
2 mA
)
≥
R
IN
Maximum expected V
------------------------------------------------------------------------------
(
)
V
–
2 mA
≥
V
IN
R
IN
V
OUT
MCP624X
+
–
V
IN
R
ISO
V
OUT
MCP624X
+
C
L
–
相關PDF資料 |
PDF描述 |
|---|---|
| MCP6271R | 170 レA, 2 MHz Rail-to-Rail Op Amp |
| MCP6271 | 300000 SYSTEM GATE 1.8 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
| MCP6273 | 300000 SYSTEM GATE 1.8 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
| MCP6274 | 300,000 SYSTEM GATE 1.8 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
| MCP6275 | 170 UA, 2 MHz Rail-to-Rail Op Amp |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP6241-E/MC | 功能描述:運算放大器 - 運放 Single 1.8V 550 kHz OP E Temp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MCP6241-E/MS | 功能描述:運算放大器 - 運放 Single 1.8V 500KHz RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MCP6241-E/MS | 制造商:Microchip Technology Inc 功能描述:; LEADED PROCESS COMPATIBLE:YES; PEAK RE |
| MCP6241-E/P | 功能描述:運算放大器 - 運放 Single 1.8V 500KHz RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MCP6241-E/SN | 功能描述:運算放大器 - 運放 Single 1.8V 500KHz RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。