- 您現在的位置：買賣IC網 > PDF目錄11427 > MC14052BCPG (ON Semiconductor)IC MUX/DEMUX DUAL 4X1 16DIP PDF資料下載
參數資料
| 型號： | MC14052BCPG |
| 廠商： | ON Semiconductor |
| 文件頁數： | 11/12頁 |
| 文件大小： | 0K |
| 描述： | IC MUX/DEMUX DUAL 4X1 16DIP |
| 標準包裝： | 500 |
| 系列： | 4000B |
| 功能： | 多路復用器/多路分解器 |
| 電路： | DP4T |
| 導通狀態電阻： | 280 歐姆 |
| 電壓電源： | 雙電源 |
| 電壓 - 電源，單路/雙路(±)： | ±3 V ~ 18 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 16-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 16-DIP |
| 包裝： | 管件 |
| 產品目錄頁面： | 1115 (CN2011-ZH PDF) |
| 其它名稱： | MC14052BCPGOS |
MC14051B, MC14052B, MC14053B
http://onsemi.com
8
APPLICATIONS INFORMATION
Figure A illustrates use of the onchip level converter
detailed in Figures 2, 3, and 4. The 0to5 V Digital Control
signal is used to directly control a 9 Vpp analog signal.
The digital control logic levels are determined by VDD
and VSS. The VDD voltage is the logic high voltage; the VSS
voltage is logic low. For the example, VDD = + 5 V = logic
high at the control inputs; VSS = GND = 0 V = logic low.
The maximum analog signal level is determined by VDD
and VEE. The VDD voltage determines the maximum
recommended peak above VSS. The VEE voltage
determines the maximum swing below VSS. For the
example, VDD VSS = 5 V maximum swing above VSS;
VSS VEE = 5 V maximum swing below VSS. The example
shows a
± 4.5 V signal which allows a 1/2 volt margin at each
peak. If voltage transients above VDD and/or below VEE are
anticipated on the analog channels, external diodes (Dx) are
recommended as shown in Figure B. These diodes should be
small signal types able to absorb the maximum anticipated
current surges during clipping.
The absolute maximum potential difference between
VDD and VEE is 18.0 V. Most parameters are specified up to
15 V which is the recommended maximum difference
between VDD and VEE.
Balanced supplies are not required. However, VSS must
be greater than or equal to VEE. For example, VDD = + 10
V, VSS = + 5 V, and VEE – 3 V is acceptable. See the Table
below.
Figure A. Application Example
+5 V
- 5 V
VDD
VSS
VEE
9 Vp-p
ANALOG SIGNAL
0-TO-5 V DIGITAL
CONTROL SIGNALS
SWITCH
I/O
INHIBIT,
A, B, C
COMMON
O/I
9 Vp-p
ANALOG SIGNAL
+ 4.5 V
4.5 V
GND
+5 V
EXTERNAL
CMOS
DIGITAL
CIRCUITRY
MC14051B
MC14052B
MC14053B
Figure B. External Germanium or Schottky Clipping Diodes
VDD
VEE
DX
ANALOG
I/O
COMMON
O/I
POSSIBLE SUPPLY CONNECTIONS
VDD
In Volts
VSS
In Volts
VEE
In Volts
Control Inputs
Logic High/Logic Low
In Volts
Maximum Analog Signal Range
In Volts
+ 8
0
– 8
+ 8/0
+ 8 to – 8 = 16 Vp–p
+ 5
0
– 12
+ 5/0
+ 5 to – 12 = 17 Vp–p
+ 5
0
0
+ 5/0
+ 5 to 0 = 5 Vp–p
+ 5
0
– 5
+ 5/0
+ 5 to – 5 = 10 Vp–p
+ 10
+ 5
– 5
+ 10/ + 5
+ 10 to – 5 = 15 Vp–p
相關PDF資料 |
PDF描述 |
|---|---|
| PIC18LF2410-I/ML | IC PIC MCU FLASH 8KX16 28QFN |
| PIC32MX220F032B-I/SO | IC MCU 32BIT 32KB FLASH 28SOIC |
| MC74LVXT4066DTRG | IC MUX/DEMUX QUAD 1X1 14TSSOP |
| DSPIC33FJ32GP302-E/SO | IC DSPIC MCU/DSP 32K 28-SOIC |
| MC14051BCPG | IC MUX/DEMUX 8X1 16DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC14052BD | 功能描述:多路器開關 IC 3-18V DP4T Analog Sw RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MC14052BD MOT92 | 制造商:Motorola 功能描述:4052BD |
| MC14052BDG | 功能描述:多路器開關 IC 3-18V DP4T Analog Sw -55 to 125 deg C RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MC14052BDMOT92 | 制造商:Motorola 功能描述:4052BD |
| MC14052BDR2 | 功能描述:多路器開關 IC 3-18V DP4T Analog Sw RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。