<var id="decup"><dl id="decup"><xmp id="decup">
  • <table id="decup"></table>
  • <rt id="decup"><delect id="decup"><dfn id="decup"></dfn></delect></rt>
    參數資料
    型號: MAX4410EUD+
    廠商: Maxim Integrated Products
    文件頁數: 8/20頁
    文件大?。?/td> 0K
    描述: IC AMP AUDIO .08W STER 14TSSOP
    產品培訓模塊: Lead (SnPb) Finish for COTS
    Obsolescence Mitigation Program
    標準包裝: 96
    系列: DirectDrive®
    類型: AB 類
    輸出類型: 耳機,2-通道(立體聲)
    在某負載時最大輸出功率 x 通道數量: 80mW x 2 @ 16 歐姆
    電源電壓: 1.8 V ~ 3.6 V
    特點: 消除爆音,短路保護和熱保護,關閉
    安裝類型: 表面貼裝
    供應商設備封裝: 14-TSSOP
    封裝/外殼: 14-TSSOP(0.173",4.40mm 寬)
    包裝: 管件
    產品目錄頁面: 1390 (CN2011-ZH PDF)
    MAX4410
    80mW, DirectDrive Stereo Headphone Driver
    with Shutdown
    16
    ______________________________________________________________________________________
    Output Capacitor (C2)
    The output capacitor value and ESR directly affect the
    ripple at PVSS. Increasing the value of C2 reduces out-
    put ripple. Likewise, decreasing the ESR of C2
    reduces both ripple and output resistance. Lower
    capacitance values can be used in systems with low
    maximum output power levels. See the Output Power
    vs. Charge-Pump Capacitance and Load Resistance
    graph in the Typical Operating Characteristics.
    Power-Supply Bypass Capacitor
    The power-supply bypass capacitor (C3) lowers the out-
    put impedance of the power supply, and reduces the
    impact of the MAX4410’s charge-pump switching tran-
    sients. Bypass PVDD with C3, the same value as C1, and
    place it physically close to the PVDD and PGND pins
    (refer to the MAX4410 EV kit for a suggested layout).
    Adding Volume Control
    The addition of a digital potentiometer provides simple
    volume control. Figure 5 shows the MAX4410 with the
    MAX5408 dual log taper digital potentiometer used as
    an input attenuator. Connect the high terminal of the
    MAX5408 to the audio input, the low terminal to ground
    and the wiper to CIN. Setting the wiper to the top posi-
    tion passes the audio signal unattenuated. Setting the
    wiper to the lowest position fully attenuates the input.
    Layout and Grounding
    Proper layout and grounding are essential for optimum
    performance. Connect PGND and SGND together at a
    single point on the PC board. Connect all components
    associated with the charge pump (C2 and C3) to the
    PGND plane. Connect PVDD and SVDD together at the
    device. Connect PVSS and SVSS together at the
    device. Bypassing of both supplies is accomplished
    by charge-pump capacitors C2 and C3 (see Typical
    Application Circuit). Place capacitors C2 and C3 as
    close to the device as possible. Route PGND and all
    traces that carry switching transients away from SGND
    and the traces and components in the audio signal
    path. Refer to the layout example in the MAX4410 EV
    kit datasheet.
    When using the MAX4410 in a UCSP package, make
    sure the traces to OUTR (bump C2) are wide enough
    to handle the maximum expected current flow. Multiple
    traces may be necessary.
    UCSP Considerations
    For general UCSP information and PC layout consider-
    ations, refer to the Maxim Application Note: Wafer-
    Level Ultra Chip-Scale Package.
    OUTL
    MAX4410
    INL
    10
    MAX5408
    H0
    L0
    5
    6
    W0A
    7
    LEFT AUDIO
    INPUT
    13
    W1A
    10
    CIN
    RIN
    CIN
    RIGHT AUDIO
    INPUT
    INR
    OUTR
    RF
    11
    8
    H1
    L1
    12
    11
    RIN
    Figure 5. MAX4410 and MAX5408 Volume Control Circuit
    相關PDF資料
    PDF描述
    MAX9725CETC+T IC AMP AUDIO .025W STER 12TQFN
    17282-2PG-3ES CONN RCPT 2POS PNL MNT PIN
    7280-3SG-300 CONN RCPT 3POS PNL MNT SKT
    MAX9736AETJ+T IC AMP AUDIO 35W MONO D 32TQFN
    18280-2SG-318 CONN RCPT 2POS CABLE SKT
    相關代理商/技術參數
    參數描述
    MAX4410EUD+ 功能描述:音頻放大器 80mW DirectDrive Stereo Headphone Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
    MAX4410EUD+T 功能描述:音頻放大器 80mW DirectDrive Stereo Headphone Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
    MAX4410EUD-T 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
    MAX4410EVKIT 功能描述:音頻 IC 開發工具 MAX4410 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
    MAX4411BEBE 制造商:Maxim Integrated Products 功能描述:80MW 2V/V FIXED GAIN DIRECTDRIVE HP - Rail/Tube