- 您現在的位置：買賣IC網 > PDF目錄359080 > M58LT128GST1ZA5F (意法半導體) 128Mbit (8Mb x16, Multiple Bank, Multi-Level, Burst) 1.8V Supply Secure Flash Memories PDF資料下載
參數資料
| 型號： | M58LT128GST1ZA5F |
| 廠商： | 意法半導體 |
| 英文描述： | 128Mbit (8Mb x16, Multiple Bank, Multi-Level, Burst) 1.8V Supply Secure Flash Memories |
| 中文描述： | 128Mbit（8兆x16插槽，多銀行，多層次，多突發）1.8V電源安全閃存 |
| 文件頁數： | 19/98頁 |
| 文件大?。?/td> | 693K |
| 代理商： | M58LT128GST1ZA5F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁
M58LT128GST, M58LT128GSB
4 Command Interface
19/98
4.1
Read Array command
The Read Array command returns the addressed bank to Read Array mode.
One Bus Write cycle is required to issue the Read Array command. Once a bank is in Read
Array mode, subsequent read operations will output the data from the memory array.
A Read Array command can be issued to any banks while programming or erasing in another
bank.
If the Read Array command is issued to a bank currently executing a program or erase
operation, the bank will return to Read Array mode but the program or erase operation will
continue, however the data output from the bank is not guaranteed until the program or erase
operation has finished. The read modes of other banks are not affected.
4.2
Read Status Register command
The device contains a Status Register that is used to monitor program or erase operations.
The Read Status Register command is used to read the contents of the Status Register for the
addressed bank.
One Bus Write cycle is required to issue the Read Status Register command. Once a bank is in
Read Status Register mode, subsequent read operations will output the contents of the Status
Register.
The Status Register data is latched on the falling edge of the Chip Enable or Output Enable
signals. Either Chip Enable or Output Enable must be toggled to update the Status Register
data
The Read Status Register command can be issued at any time, even during program or erase
operations. The Read Status Register command will only change the read mode of the
addressed bank. The read modes of other banks are not affected. Only Asynchronous Read
and Single Synchronous Read operations should be used to read the Status Register. A Read
Array command is required to return the bank to Read Array mode.
See
Table 9
for the description of the Status Register Bits.
4.3
Read Electronic Signature command
The Read Electronic Signature command is used to read the Manufacturer and Device Codes,
the Protection Status of the addressed bank, the Configuration Register and the Protection
Register.
One Bus Write cycle is required to issue the Read Electronic Signature command. Once a bank
is in Read Electronic Signature mode, subsequent read operations in the same bank will output
the Manufacturer Code, the Device Code, the Protection Status of the addressed bank, or the
Configuration Register (see
Table 7
).
The Read Electronic Signature command can be issued at any time, even during program or
erase operations, except during Protection Register Program operations. Dual operations
between the Parameter bank and the Electronic Signature location are not allowed (see
Table 15: Dual Operation Limitations
for details).
If a Read Electronic Signature command is issued to a bank that is executing a program or
erase operation the bank will go into Read Electronic Signature mode. Subsequent Bus Read
相關PDF資料 |
PDF描述 |
|---|---|
| M58LT128GST | 128Mbit (8Mb x16, Multiple Bank, Multi-Level, Burst) 1.8V Supply Secure Flash Memories |
| M58LV064A150ZA1T | 64 Mbit 4Mb x16 or 2Mb x32, Uniform Block, Burst 3V Supply Flash Memories |
| M58LV064A | 64 Mbit 4Mb x16 or 2Mb x32, Uniform Block, Burst 3V Supply Flash Memories |
| M58LV064A150N1T | 64 Mbit 4Mb x16 or 2Mb x32, Uniform Block, Burst 3V Supply Flash Memories |
| M58LV064A150N6T | 64 Mbit 4Mb x16 or 2Mb x32, Uniform Block, Burst 3V Supply Flash Memories |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M58LT128HSB | 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:128 Mbit (8 Mb 】16, multiple bank, multilevel interface, burst) 1.8 V supply, secure Flash memories |
| M58LT128HSB8ZA6 | 制造商:Micron Technology Inc 功能描述:NOR Flash Parallel/Serial 1.8V 128Mbit 8M x 16bit 85ns 64-Pin TBGA Tray 制造商:Micron Technology Inc 功能描述:STD FLASH - Trays |
| M58LT128HSB8ZA6E | 功能描述:IC FLASH 128MBIT 85NS 64TBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:3,000 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:32K (4K x 8) 速度:100kHz，400kHz 接口:I²C，2 線串口 電源電壓:2.5 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:帶卷 (TR) 其它名稱:CAV24C32WE-GT3OSTR |
| M58LT128HSB8ZA6F | 功能描述:IC FLASH 128MBIT 85NS 64TBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:2,500 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（單線） 電源電壓:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) |
| M58LT128HSB8ZA6T | 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:128 Mbit (8 Mb 】16, multiple bank, multilevel interface, burst) 1.8 V supply, secure Flash memories |
發布緊急采購，3分鐘左右您將得到回復。