- 您現在的位置：買賣IC網 > PDF目錄359080 > M58BW032DT60ZA3T (意法半導體) 32 Mbit (1Mb x32, Boot Block, Burst) 3.3V Supply Flash Memory PDF資料下載
參數資料
| 型號： | M58BW032DT60ZA3T |
| 廠商： | 意法半導體 |
| 英文描述： | 32 Mbit (1Mb x32, Boot Block, Burst) 3.3V Supply Flash Memory |
| 中文描述： | 32兆位（1兆X32號，引導塊，突發）3.3V電源快閃記憶體 |
| 文件頁數： | 28/60頁 |
| 文件大小： | 906K |
| 代理商： | M58BW032DT60ZA3T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
M58BW032BT, M58BW032BB, M58BW032DT, M58BW032DB
28/60
STATUS REGISTER
The Status Register provides information on the
current or previous Program, Erase, Block Protect
or Tuning Protection operation. The various bits in
the Status Register convey information and errors
on the operation. They are output on DQ7-DQ0.
To read the Status Register the Read Status Reg-
ister command can be issued. The Status Register
is automatically read after Program, Erase, Block
Protect, Program/Erase Resume commands. The
Status Register can be read from any address.
The contents of the Status Register can be updat-
ed during an erase or program operation by tog-
gling the Output Enable or Output Disable pins or
by dis-activating (Chip Enable, V
IH
) and then reac-
tivating (Chip Enable and Output Enable, V
IL
, and
Output Disable, V
IH
.) the device.
The Status Register bits are summarized in
Table
11., Status Register Bits
. Refer to Table
11
in con-
junction with the following text descriptions.
Program/Erase Controller Status (Bit 7)
The Program/Erase Controller Status bit indicates
whether the Program/Erase Controller is active or
inactive. When the Program/Erase Controller Sta-
tus bit is set to ‘0’, the Program/Erase Controller is
active; when bit7 is set to ‘1’, the Program/Erase
Controller is inactive.
The Program/Erase Controller Status is set to ‘0’
immediately after a Program/Erase Suspend com-
mand is issued until the Program/Erase Controller
pauses. After the Program/Erase Controller paus-
es the bit is set to ‘1’.
During Program and Erase operations the Pro-
gram/Erase Controller Status bit can be polled to
find the end of the operation. The other bits in the
Status Register should not be tested until the Pro-
gram/Erase Controller completes the operation
and the bit is set to ‘1’.
After the Program/Erase Controller completes its
operation the Erase Status (bit5), Program/Tuning
Protection Unlock status (bit4) bits should be test-
ed for errors.
Erase Suspend Status (Bit 6)
The Erase Suspend Status bit indicates that an
Erase operation has been suspended and is wait-
ing to be resumed. The Erase Suspend Status
should only be considered valid when the Pro-
gram/Erase Controller Status bit is set to ‘1’ (Pro-
gram/Erase Controller inactive); after a Program/
Erase Suspend command is issued the memory
may still complete the operation rather than enter-
ing the Suspend mode.
When the Erase Suspend Status bit is set to ‘0’,
the Program/Erase Controller is active or has com-
pleted its operation; when the bit is set to ‘1’, a Pro-
gram/Erase Suspend command has been issued
and the memory is waiting for a Program/Erase
Resume command.
When a Program/Erase Resume command is is-
sued the Erase Suspend Status bit returns to ‘0’.
Erase Status (Bit 5)
The Erase Status bit can be used to identify if the
memory has failed to verify that the block has
erased correctly. The Erase Status bit should be
read once the Program/Erase Controller Status bit
is High (Program/Erase Controller inactive).
When the Erase Status bit is set to ‘0’, the memory
has successfully verified that the block has erased
correctly. When the Erase Status bit is set to ‘1’,
the Program/Erase Controller has applied the
maximum number of pulses to the block and still
failed to verify that the block has erased correctly.
Once set to ‘1’, the Erase Status bit can only be re-
set to ‘0’ by a Clear Status Register command or a
hardware reset. If set to ‘1’ it should be reset be-
fore a new Program or Erase command is issued,
otherwise the new command will appear to fail.
Program/ Write to Buffer and Program/Tuning
Protection Unlock Status (Bit 4)
The Program/Write to Buffer and Program/Tuning
Protection Unlock Status bit is used to identify a
Program failure, a Write to Buffer and Program
failure or a Tuning Protection Code verify failure.
Bit4 should be read once the Program/Erase Con-
troller Status bit is High (Program/Erase Controller
inactive).
When bit4 is set to ‘0’ the memory has successful-
ly verified that the device has programmed cor-
rectly or that the correct Tuning Protection Code
has been written. When bit4 is set to ‘1’ the device
has failed to verify that the data has been pro-
grammed correctly or that the correct Tuning Pro-
tection code has been written.
Once set to 1’, the Program Status bit can only be
reset to ‘0’ by a Clear Status Register command or
a hardware reset. If set to ‘1’ it should be reset be-
fore a new Program or Erase command is issued,
otherwise the new command will appear to fail.
V
PEN
Status (Bit 3).
The V
PEN
Status bit can be
used to identify if a program or erase operation
has been attempted when V
PEN
is Low, V
IL
.
When Bit 3 is set to ‘0’ no program or erase oper-
ations have been attempted with V
PEN
Low, V
IL
,
since the last Clear Status Register command, or
hardware reset.
When Bit 3 is set to ‘1’ a program or erase opera-
tion has been attempted with V
PEN
Low, V
IL
.
Once set to ‘1’, Bit 3 can only be reset by an Clear
Status Register command or a hardware reset. If
set to ‘1’ it should be reset before a new program
相關PDF資料 |
PDF描述 |
|---|---|
| M58CR064C12ZB6T | 64 Mbit 4Mb x 16, Dual Bank, Burst 1.8V Supply Flash Memory |
| M58CR064D12ZB6T | 64 Mbit 4Mb x 16, Dual Bank, Burst 1.8V Supply Flash Memory |
| M58CR064P12ZB6T | 64 Mbit 4Mb x 16, Dual Bank, Burst 1.8V Supply Flash Memory |
| M58CR064Q12ZB6T | 64 Mbit 4Mb x 16, Dual Bank, Burst 1.8V Supply Flash Memory |
| M58CR064D85ZB6T | 64 Mbit 4Mb x 16, Dual Bank, Burst 1.8V Supply Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M58BW032DT60ZA6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:32 Mbit (1Mb x32, Boot Block, Burst) 3.3V Supply Flash Memory |
| M58BW16F | 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:16 or 32 Mbit (x 32, boot block, burst) 3.3 V supply Flash memories |
| M58BW16FB4D150 | 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Trays |
| M58BW16FB4T3 | 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:16 or 32 Mbit (x 32, boot block, burst) 3.3 V supply Flash memories |
| M58BW16FB4T3F | 功能描述:IC FLASH 16MBIT 45NS 80PQFP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 產品變化通告:Product Discontinuation 26/Apr/2010 標準包裝:136 系列:- 格式 - 存儲器:RAM 存儲器類型:SRAM - 同步，DDR II 存儲容量:18M（1M x 18） 速度:200MHz 接口:并聯 電源電壓:1.7 V ~ 1.9 V 工作溫度:0°C ~ 70°C 封裝/外殼:165-TBGA 供應商設備封裝:165-CABGA（13x15） 包裝:托盤 其它名稱:71P71804S200BQ |
發布緊急采購，3分鐘左右您將得到回復。