<nobr id="5uray"><span id="5uray"></span></nobr>
<thead id="5uray"></thead>
<ins id="5uray"><noframes id="5uray"></noframes></ins><wbr id="5uray"><span id="5uray"></span></wbr>
  • <big id="5uray"><sup id="5uray"><tbody id="5uray"></tbody></sup></big>
  • <ins id="5uray"><noframes id="5uray"><nobr id="5uray"></nobr></noframes></ins>
    <dl id="5uray"><sup id="5uray"><ins id="5uray"></ins></sup></dl>
    參數資料
    型號: M48T59-70PC1
    廠商: 意法半導體
    英文描述: 64 Kbit 8Kb x8 TIMEKEEPER SRAM
    中文描述: 64千位8KB的x8 SRAM的計時器
    文件頁數: 10/21頁
    文件大?。?/td> 168K
    代理商: M48T59-70PC1
    M48T59, M48T59Y, M48T59V
    10/21
    condition reset will not occur unless the addresses
    are stable at the flag location for at least 15ns
    while the divice is in the read mode as shown in
    Figure 11.
    The IRQ/FT pin is an open drain output and re-
    quires a pull-up resistor (10k
    recommended) to
    V
    CC
    . The pin remains in the high impedance state
    unless an interrupt occurs or the frequency test
    mode is enabled.
    CLOCK OPERATIONS
    Reading the Clock
    Updates to the TIMEKEEPER registers should be
    halted before clock data is read to prevent reading
    data in transition. Because the BiPORT TIME-
    KEEPER cells in the RAM array are only data reg-
    isters, and not the actual clock counters, updating
    the registers can be halted without disturbing the
    clock itself.
    Updating is halted when a ’1’ is written to the
    READ bit, D6 in the Control register (1FF8h). As
    long as a ’1’ remains in that position, updating is
    halted.
    After a halt is issued, the registers reflect the
    count; that is, the day, date, and the time that were
    current at the moment the halt command was is-
    sued.
    All of the TIMEKEEPER registers are updated si-
    multaneously. A halt will not interrupt an update in
    progress. Updating is within a second after the bit
    is reset to a ’0’.
    Setting the Clock
    Bit D7 of the Control register (1FF8h) is the
    WRITE bit. Setting the WRITE bit to a ’1’, like the
    READ bit, halts updates to the TIMEKEEPER reg-
    during the time the device is sampling V
    CC
    . There-
    fore, decoupling of the power supply lines is rec-
    ommended.
    When V
    CC
    drops below V
    SO
    , the control circuit
    switches power to the internal battery which pre-
    serves data and powers the clock. The internal
    button cell will maintain data in the M48T59/59Y/
    59V for an accumulated period of at least 7 years
    when V
    CC
    is less than V
    SO
    . As system power re-
    turns and V
    CC
    rises above V
    SO
    , the battery is dis-
    connected, and the power supply is switched to
    external V
    CC
    . Deselect continues for t
    REC
    after
    V
    CC
    reaches V
    PFD
    (max).
    For more information on Battery Storage Life refer
    to the Application Note AN1012.
    POWER-ON RESET
    The M48T59/59Y/59V continuously monitors V
    CC
    .
    When V
    CC
    falls to the power fail detect trip point,
    the RST pulls low (open drain) and remains low on
    power-up for 40ms to 200ms after V
    CC
    passes
    V
    PFD
    . RST is valid for all V
    CC
    conditions. The RST
    pin is an open drain output and an appropriate re-
    sistor to V
    CC
    should be chosen to control rise time.
    PROGRAMMABLE INTERRUPTS
    The M48T59/59Y/59V provides two programma-
    ble interrupts; an alarm and a watchdog. When an
    interrupt condition occurs, the M48T59/59Y/59V
    sets the appropriate flag bit in the flag register
    1FF0h. The interrupt enable bits in (AFE and ABE)
    in 1FF6h and the Watchdog Steering (WDS) bit in
    1FF7h allow the interrupt to activate the IRQ/FT
    pin.
    The interrupt flags and the IRQ/FT output are
    cleared by a read to the flags register. An interrupt
    Figure 9. Clock Calibration
    AI00594B
    NORMAL
    POSITIVE
    CALIBRATION
    NEGATIVE
    CALIBRATION
    相關PDF資料
    PDF描述
    M48T59-70PC1TR 64 Kbit 8Kb x8 TIMEKEEPER SRAM
    M48T59-70PC6 64 Kbit 8Kb x8 TIMEKEEPER SRAM
    M48T59-70PC6TR 64 Kbit 8Kb x8 TIMEKEEPER SRAM
    M48T59VPC 64 Kbit 8Kb x8 TIMEKEEPER SRAM
    M48T59VSH 64 Kbit 8Kb x8 TIMEKEEPER SRAM
    相關代理商/技術參數
    參數描述
    M48T59-70PC1E 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5.0 or 3.3 V, 64 Kbit (8 Kbit x 8) TIMEKEEPER? SRAM
    M48T59-70PC1F 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5.0 or 3.3 V, 64 Kbit (8 Kbit x 8) TIMEKEEPER? SRAM
    M48T59-70PC1TR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:64 Kbit 8Kb x8 TIMEKEEPER SRAM
    M48T59-70PC6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:64 Kbit 8Kb x8 TIMEKEEPER SRAM
    M48T59-70PC6TR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:64 Kbit 8Kb x8 TIMEKEEPER SRAM