參數資料
型號: M41T60
廠商: 意法半導體
英文描述: Serial Access Real-Time Clock
中文描述: 串行訪問實時時鐘
文件頁數: 8/23頁
文件大小: 346K
代理商: M41T60
M41T60
8/23
READ Mode
In this mode, the master reads the M41T60 slave
after setting the slave address (see Figure
9
). Fol-
lowing the WRITE Mode Control Bit (R/W = 0) and
the Acknowledge Bit, the word address An is writ-
ten to the on-chip address pointer. Next the
START condition and slave address are repeated,
followed by the READ Mode Control Bit (R/W = 1).
At this point, the master transmitter becomes the
master receiver. The data byte which was ad-
dressed will be transmitted and the master receiv-
er will send an Acknowledge Bit to the slave
transmitter. The address pointer is only increment-
ed on reception of an Acknowledge Bit. The
M41T60 slave transmitter will now place the data
byte at address A
n+1
on the bus. The master re-
ceiver reads and acknowledges the new byte and
the address pointer is incremented to A
n+2
.
This cycle of reading consecutive addresses will
continue until the master receiver sends a STOP
condition to the slave transmitter.
The system-to-user transfer of clock data will be
halted whenever the address being read is a clock
address (0h to 6h). The update will resume due to
a Stop Condition or when the pointer increments to
any non-clock address (7h).
An alternate READ Mode may also be implement-
ed, whereby the master reads the M41T60 slave
without first writing to the (volatile) address point-
er. The first address that is read is the last one
stored in the pointer (see
Figure 11., page 9
).
WRITE Mode
In this mode the master transmitter transmits to
the M41T60 slave receiver. Bus protocol is shown
in
Figure 12., page 9
. Following the START condi-
tion and slave address, a logic '0' (R/W = 0) is
placed on the bus and indicates to the addressed
device that word address An will follow and is to be
written to the on-chip address pointer. The data
word to be written to the memory is strobed in next
and the internal address pointer is incremented to
the next address location on the reception of an
acknowledge clock. The M41T60 slave receiver
will send an acknowledge clock to the master
transmitter after it has received the slave address
and again after it has received the word address
and each data byte (see Figure
9
).
Figure 9. Slave Address Location
AI00602
R/W
SLAVE ADDRESS
START
A
0
1
0
0
0
1
1
M
L
相關PDF資料
PDF描述
M41T60Q6F Serial Access Real-Time Clock
M41T64 Serial Access Real-Time Clock with Alarms
M41T80 Vandal Resistant Pushbutton Switch; Illumination:Illuminated; Actuator Style:Round; Actuator Diameter:22mm; Circuitry:SPST; Switch Operation:Push to Make; Switch Terminals:Screw; Contact Current Max:50mA
M41T80M Vandal Resistant Pushbutton Switch; Illumination:Illuminated; Actuator Style:Round; Actuator Diameter:22mm; Circuitry:SPST; Switch Operation:Push to Make; Switch Terminals:Screw; Contact Current Max:50mA
M41T80M6 SWITCH, VR, ILLUM, GREEN/BLUE; Switch function type:SPNO; Voltage, contact DC max:24V; Temp, op. max:70(degree C); Temp, op. min:-30(degree C); Diameter, panel cut-out:19.2mm; Length / Height, external:31mm; Depth, external:30.3mm; RoHS Compliant: Yes
相關代理商/技術參數
參數描述
M41T60_05 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Serial access real-time clock
M41T60_10 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Serial access real-time clock
M41T60Q6F 功能描述:實時時鐘 1.3V to 3.6V RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
M41T60Q6F-CUT TAPE 制造商:ST 功能描述:M41T60 Series 1.3 to 4.4 V Serial I2C Real Time Clock Surface Mount - QFN-16
M41T62 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Serial Access Real-Time Clock with Alarms