參數資料
型號： LTC4264IDE#PBF
廠商： Linear Technology
文件頁數： 13/24頁
文件大?。?/td> 0K
描述： IC CNTRLR PD INTERFACE 12-DFN
產品培訓模塊： Power over Ethernet
標準包裝： 91
控制器類型： 以太網供電控制器（POE）
接口： IEEE 802.3af
電流 - 電源： 3mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 12-WFDFN 裸露焊盤
供應商設備封裝： 12-DFN（4x3）
包裝： 管件
LTC4264
20
4264f
APPLICATIONS INFORMATION
Shutdown Interface
To disable the 25k signature resistor, connect SHDN to
the GND pin. Alternately, the SHDN pin can be driven
high with respect to VIN. Examples of interface circuits
that disable the signature and all LTC4264 functions are
shown in Figure 10, options 2 and 4. Note that the SHDN
input resistance is relatively large and the threshold volt-
age is fairly low. Because of high voltages present on the
printed circuit board, leakage currents from the GND pin
could inadvertently pull SHDN high. To ensure trouble-free
operation, use high voltage layout techniques in the vicinity
of SHDN. If unused, connect SHDN directly to VIN.
Load Capacitor
The IEEE 802.3af specication requires that the PD maintain
a minimum load capacitance of 5F. It is permissible to
have a much larger load capacitor and the LTC4264 can
charge very large load capacitors before thermal issues
become a problem. However, the load capacitor must not
be too large or the PD design may violate IEEE 802.3af
requirements. The LTC4264 maintains IEEE 802.3af com-
pliance when the load capacitor is 180F or less. A larger
capacitor can be employed in a proprietary, close-system
high power application.
If the load capacitor is too large, there can be a prob-
lem with inadvertent power shutdown by the PSE. For
example, if the PSE is running at –57V (IEEE 802.3af
maximum allowed) and the PD is detected and powered
up, the load capacitor will be charged to nearly –57V. If
for some reason the PSE voltage is suddenly reduced to
–44V (IEEE 802.3af minimum allowed), the input bridge
will reverse bias and the PD power will be supplied by the
load capacitor. Depending on the size of the load capacitor
and the DC load of the PD, the PD will not draw any power
from the PSE for a period of time. If this period of time
exceeds the IEEE 802.3af 300ms disconnect delay, the
PSE will remove power from the PD. For this reason, it is
necessary to evaluate the load current and capacitance to
ensure that inadvertent shutdown cannot occur.
Refer also to Thermal Protection in this data sheet for
further discussion on load capacitor selection.
MAINTAIN POWER SIGNATURE
In an IEEE 802.3af system, the PSE uses the maintain
power signature (MPS) to determine if a PD continues to
require power. The MPS requires the PD to periodically
draw at least 10mA and also have an AC impedance less
than 26.25k
Ω in parallel with 0.05F. If either the DC
current is less than 10mA or the AC impedance is above
26.25k
Ω, the PSE may disconnect power. The DC current
must be less than 5mA and the AC impedance must be
above 2M
Ω to guarantee power will be removed. The PD
application circuits shown in this data sheet present the
required AC impedance necessary to maintain power.
LAYOUT CONSIDERATIONS FOR THE LTC4264
The LTC4264 is relatively immune to layout problems.
Excessive parasitic capacitance on the RCLASS pin should
be avoided. Include an electrically isolated heat sink to
which the exposed pad on the bottom of the package can
be soldered. For optimum thermal performance, make the
heat sink as large as possible. Voltages in a PD can be as
large as –57V for PoE applications, so high voltage layout
techniques should be employed. The SHDN pin should
be separated from other high voltage pins, like GND and
相關PDF資料
PDF描述
PIC16F722-E/MV IC MCU 8BIT 3.5KB FLASH 28UQFN
PIC16LF722-E/ML IC PIC MCU FLASH 3.5KB 28-QFN
PIC16F689-E/SS IC PIC MCU FLASH 4KX14 20SSOP
PIC16F685-E/SS IC PIC MCU FLASH 4KX14 20SSOP
KSZ8895RQI IC 10/100-T 5 PORT SW 128PQFP
相關代理商/技術參數
參數描述
LTC4265 制造商:LINER 制造商全稱:Linear Technology 功能描述:Quad IEEE 802.3at Power over Ethernet Controller
LTC4265CDE#PBF 功能描述:IC CTRLR PD INTERFACE HP 12-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
LTC4265CDE#TRPBF 功能描述:IC CTRLR PD INTERFACE HP 12-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
LTC4265CDE-PBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:IEEE 802.3at High Power PD Interface Controller with 2-Event Classifi cation Recognition
LTC4265CDE-TRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:IEEE 802.3at High Power PD Interface Controller with 2-Event Classifi cation Recognition
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*