For more information www.linear.com/LTC2758 PIN FUNCTIONS REFA (Pins 1, 2): Feedback R" />
參數資料
型號： LTC2758BILX#PBF
廠商： Linear Technology
文件頁數： 23/24頁
文件大小： 0K
描述： IC DAC 18BIT SPI/SRL 48-LQFP
標準包裝： 250
系列： SoftSpan™
設置時間： 2.1µs
位數： 18
數據接口： 串行，SPI?
轉換器數目： 2
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 48-LQFP
供應商設備封裝： 48-LQFP（7x7）
包裝： 管件
輸出數目和類型： 2 電流，單極；4 電流，雙極
配用： DC1684A-A-ND - BOARD DAC LTC2758
LTC2758
8
2758fa
For more information www.linear.com/LTC2758
PIN FUNCTIONS
REFA (Pins 1, 2): Feedback Resistor for the DAC A Refer-
ence Inverting Amplifier, and Reference Input for DAC A.
The 20k feedback resistor is connected internally from
REFA to RCOMA. For normal operation tie this pin to the
output of the DAC A reference inverting amplifier (see
Typical Application). Typically –5V; accepts up to ±15V.
Pins 1 and 2 are internally shorted together.
RCOMA (Pin 3): Virtual Ground Point for the DAC A Ref-
erence Amplifier Inverting Resistors. The 20k reference
inverting resistors are connected internally from RINA to
RCOMA and from RCOMA to REFA, respectively (see Block
Diagram). For normal operation tie RCOMA to the negative
input of the external reference inverting amplifier (see
Typical Application).
GEADJA (Pin 4): Gain Adjust Pin for DAC A. This control pin
canbeusedtonullgainerrorortocompensateforreference
errors. The gain change expressed in LSB is the same for
anyoutputrange.SeeSystemOffsetandGainAdjustments
in the Operation section. Tie to ground if not used.
RINA (Pins 5, 6): Input Resistor for the DAC A External
Reference Inverting Amplifier. The 20k input resistor is
connected internally from RINA to RCOMA. For normal op-
eration tie RINA to the external positive reference voltage
(seeTypicalApplication).Eitherorbothoftheseprecision-
matched resistor sets (each set comprising RINX, RCOMX
and REFX) may be used to invert positive references to
provide the negative voltages needed by the DACs. Typi-
cally 5V; accepts up to ±15V. Pins 5 and 6 are internally
shorted together.
GND (Pins 7, 10, 15, 17, 18, 27, 30): Ground; tie to
ground.
IOUT2AS, IOUT2AF (Pins 8, 9): DAC A Current Output
Complement Sense and Force Pins. Tie to ground via a
clean, low-impedance path. These pins may be used with
a precision ground buffer amp as a Kelvin sensing pair
(see the Applications Information section).
CS/LD (Pin 11): Synchronous Chip Select and Load Input
Pin.
SDI (Pin 12): Serial Data Input. Data is clocked in on the
rising edge of the serial clock (SCK) when CS/LD is low.
SCK (Pin 13): Serial Clock Input.
SRO (Pin 14): Serial Readback Output. Data is clocked out
on the falling edge of SCK. Readback data begins clocking
out after the last address bit A0 is clocked in. SRO is an
active output only when the chip is selected (i.e., when
CS/LD is low). Otherwise SRO presents a high-impedance
output in order to allow other parts to control the bus.
VDD(Pin16):PositiveSupplyInput;2.7V≤VDD≤5.5V.By-
pass with a 0.1μF low-ESR ceramic capacitor to ground.
CLR (Pin 19): Asynchronous Clear Input. When this pin is
low, all DAC registers (both code and span) are cleared to
zero. All DAC outputs are cleared to zero volts.
RFLAG (Pin 20): Reset Flag Output. An active low output
is asserted when there is a power-on reset or a clear event.
Returns high when an Update command is executed.
DNC (Pin 21): Do Not Connect.
M-SPAN (Pin 22): Manual Span Control Pin. M-SPAN is
used in conjunction with pins S2, S1 and S0 (Pins 25, 24
and 23) to configure all DACs for operation in a single,
fixed output range.
To configure the part for manual-span use, tie M-SPAN
directly to VDD. The DAC output range is then set via
hardware pin strapping of pins S2, S1 and S0 (rather than
through the SPI port); and Write and Update commands
have no effect on the active output span.
ToconfigurethepartforSoftSpanuse,tieM-SPANdirectly
to GND. The output ranges are then individually control-
lable through the SPI port; and pins S2, S1 and S0 have
no effect.
SeeManualSpanConfigurationintheOperationsection.M-
SPAN must be connected either directly to GND (SoftSpan
configuration) or to VDD (manual-span configuration).
S0 (Pin 23): Span Bit 0 Input. In Manual Span mode (M-
SPAN tied to VDD), Pins S0, S1 and S2 are pin-strapped
to select a single fixed output range for all DACs. These
pins should be tied to either GND or VDD even if they are
unused.
S1 (Pin 24): Span Bit 1 Input. In Manual Span mode (M-
SPAN tied to VDD), Pins S0, S1 and S2 are pin-strapped to
select a single fixed output range for all DACs. These pins
shouldbetiedtoeitherGNDorVDDeveniftheyareunused.
相關PDF資料
PDF描述
AD569JPZ-REEL IC DAC 16BIT MONO NON-LIN 28PLCC
VE-BND-MU-S CONVERTER MOD DC/DC 85V 200W
VE-JW0-MZ-B1 CONVERTER MOD DC/DC 5V 25W
VE-J1F-MZ-B1 CONVERTER MOD DC/DC 72V 25W
VE-J14-MZ-B1 CONVERTER MOD DC/DC 48V 25W
相關代理商/技術參數
參數描述
LTC28 制造商:3M Electronic Products Division 功能描述:28 way professional IC test clip,0.6in
LTC2801CDE 制造商:Linear Technology 功能描述:Single Transmitter/Receiver RS-232 12-Pin DFN EP
LTC2801CDE#PBF 功能描述:IC TXRX RS232 12-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:27 系列:- 類型:收發器 驅動器/接收器數:3/3 規程:RS232，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC 包裝:管件
LTC2801CDE#TRPBF 功能描述:IC TXRX RS232 12-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件
LTC2801IDE 制造商:Linear Technology 功能描述:Single Transmitter/Receiver RS-232 12-Pin DFN EP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*