- 您現在的位置：買賣IC網 > PDF目錄358743 > LB11827 (Sanyo Electric Co.,Ltd.) Three-Phase Brushless Motor Driver for OA Products PDF資料下載
參數資料
| 型號： | LB11827 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Three-Phase Brushless Motor Driver for OA Products |
| 中文描述： | 三相無刷電機驅動的辦公自動化產品 |
| 文件頁數： | 10/11頁 |
| 文件大?。?/td> | 144K |
| 代理商： | LB11827 |
No. 7110-10/11
LB11827
4. Power save circuit
This IC enters the power save condition to decrease the current dissipation in the stop mode. In this condition, the bias
current of most of circuits is cut off. Even in the power save condition, the 5 V regulator output is given.
5. Reference clock
This is entered from the external signal source (1 MHz max) via a resistor (reference: about 5.1 k
) in series with the
XI pin. The XO pin is left open.
Input signal source levels:
Low-level voltage: 0 to 0.8 V
High-level voltage: 2.5 to 5.0 V
6. Speed lock range
The speed lock range is ±6.25% of the constant speed. If the motor speed falls inside the lock range, the LD pin goes
to “L” (open collector output). When the motor speed falls outside the lock range, the on-duty ratio of motor drive
output changes according to the speed error, causing control to keep the motor speed within the lock range.
7. PWM frequency
PWM frequency is determined from the capacity C (F) of capacitor connected to the PWM pin.
f
PWM
≈
1/(14,400
×
C)
It is recommended to keep the PWM frequency at 15 – 25 kHz. GND of a capacitor to be connected must be connected
to the GND1 pin with the shortest possible wiring.
8. Hall input signal
The Hall input requires the signal input with an amplitude exceeding the hysteresis width (42 mV max). Considering
the effect of noise, the input with the amplitude of 100 mV or more is recommended.
When the output waveform is disturbed due to noise effects at a time of changeover of the output phase, connect a
capacitor between Hall input pins (+ and -) at a point as near as possible to the pin.
9. F/R changeover
Motor rotation direction can be changed over with the F/R pin. When changing F/R while the motor is running, pay
attention to following points.
For the through current at a time of changeover, the countermeasure is taken using a circuit. However, it is
necessary to prevent exceeding of the rated voltage (30 V) due to rise of V
CC
voltage at a time of changeover
(because the motor current returns instantaneously to the power supply). When this problem exists, increase the
capacity of a capacitor between V
CC
and GND.
When the motor current exceeds the current limit value after changeover, the lower-side Tr is turned OFF. But, the
upper-side Tr enters the short-brake condition and the current determined from the motor counter electromotive
voltage and coil resistance flows. It is necessary to prevent this current from exceeding the rated current (3.5 A).
(F/R changeover speed is dangerous.)
10. Motor lock protection circuit
A motor lock protection circuit is incorporated for protection of IC and motor when the motor is locked.
When the LD output is “H” (unlocked) for a certain period in the start condition, the lower-side Tr is turned OFF. This
time is set with the capacity of the capacitor connected to the CSD pin. The time can be set to about 3.3 seconds with
the capacity of 10 μF (variance about ±30%).
Set time (s)
≈
0.33
×
C (μF)
When the capacitor used has a leak current, due consideration is necessary because it may cause error in the set time,
etc.
Cancelling requires either the stop condition or re-application of power supply (in the stop condition). When the lock
protection circuit is not to be used, connect the CSD pin to GND.
When the stop period during which lock protection is to be cancelled is short, the charge of capacitor cannot be
discharged completely and the lock protection activation time at restart becomes shorter than the set value. It is
相關PDF資料 |
PDF描述 |
|---|---|
| LB11847 | PWM Current Control Type Stepping Motor Driver |
| LB11850VA | Monolithic Digital IC For Fan Motor Single-Phase Full-Wave Pre-Driver with Speed Control Function |
| LB11850V | Monolithic Digital IC For Fan Motor Single-Phase Full-Wave Pre-Driver with Speed Control Function |
| LB11851M | Monolithic Digital IC Microprocessor Fan Motor Interface Driver |
| LB11867FV | Monolithic Digital IC For Fan Motor Variable Speed Single-phase Full-wave Pre-driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB11847 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PWM Current Control Type Stepping Motor Driver |
| LB11847_08 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PWM Current Control Type Stepping Motor Driver |
| LB11847-E | 功能描述:馬達/運動/點火控制器和驅動器 10-45VStepping Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11847L-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11850V | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic Digital IC For Fan Motor Single-Phase Full-Wave Pre-Driver with Speed Control Function |
發布緊急采購，3分鐘左右您將得到回復。