- 您現在的位置：買賣IC網 > PDF目錄358743 > LB11824 (Sanyo Electric Co.,Ltd.) Direct PWM Drive Brushless Motor Predriver for On-Demand Water Heater and Air Conditioner Motors PDF資料下載
參數資料
| 型號： | LB11824 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Direct PWM Drive Brushless Motor Predriver for On-Demand Water Heater and Air Conditioner Motors |
| 中文描述： | 直接PWM驅動無刷電機預驅動器的按需熱水器和空調電機 |
| 文件頁數： | 16/17頁 |
| 文件大?。?/td> | 178K |
| 代理商： | LB11824 |
9. Motor lock protection circuit
A motor lock protection circuit is incorporated for protection of IC and motor when the motor is locked. When the
Hall input signal is not changed for a certain period with the motor driving, the one-side output (UH, VH, WH) is
turned OFF. The time is set by means of a capacity of a capacitor connected to the CSD pin.
Set time (s) .= 154
×
C (μF)
Addition of a 0.01 μF capacitor causes a protection time of about 1.54 seconds. (Drive is turned OFF when one cycle
of Hall input signal is longer than this time period.) The time to be set must have a sufficient allowance so that the
protection is not activated at a normal motor startup. Select the capacitor of 4700 pF or more. The protection circuit is
not activated when braking. To cancel the restriction protection condition, one of following steps must be taken:
Stop mode (10 μs or more)
Maintaining the output duty 0% condition through input of VCTL or PWMIN for more than the period of tCSD
×
2.
(tCSD (s) .= 0.5
×
C (μF). When the 0.01 μF capacitor is added, maintaining for about 10 ms or more is necessary.)
Re-application of power supply
The CSD pin acts also as an initial reset pulse generation pin and causes reset of the logic circuit when connected with
GND. Accordingly, the motor drive condition can not be obtained. When this pin is not to be used, a resistor of about
150 k
and a capacitor of about 4700 pF must be connected to GND in parallel. When the restriction protection circuit
is not used, following functions are also invalid:
Protection circuit for the reverse mode
Overheat protection circuit
10. Overheat protection circuit
One-side output (UH, VH,WH) is turned OFF when the junction temperature (Tj) exceeds a specified temperature
(TSD). Since the minimum variation of TSD is 125°C, thermal design must be made so that Tj = 125°C is not
exceeded except in the case of abnormality. Accordingly, Pdmax when Tj (max) = 125°C is 0.72 W (Ta=25°C)
When the motor lock protection is not to be used by inserting in parallel the resistor of about 150k
and capacitor of
about 4700pF between the CSD pin and GND, this overheat protection circuit does not function.
In this case, Tj (max) = 150°C, so that Pdmax = 0.9W (Ta = 25°C)
11. Forward/reverse rotation
To select forward or reverse in the rotation condition, a measure is taken to prevent flow of the through current
(through current due to the output Tr OFF delay time at selection) at the output. Selection during rotation causes the
current exceeding the current limit value to flow through the output Tr because of the motor coil resistance and motor
reverse electromotive voltage condition. It is therefore necessary to select the external output Tr that is not damaged by
this current or to select forward/reverse only when the motor rotation speed has decreased to a certain level.
12. Power supply stabilization
This IC is of a switching drive type and the power line tends to be affected. It is therefore necessary to connect a
capacitor of sufficient capacity for stabilization between the V
CC
1 pin and GND.
To insert a diode in the power line to prevent breakdown through reverse connection of power supply, the power line
becomes more readily affected. It is necessary to select a larger capacity.
To turn ON/OFF the power supply with a switch, etc., large distance between the switch and capacitor causes
substantial deviation of the supply voltage due to the line inductance and inrush current into the capacitor. In certain
cases, the withstand voltage may be exceeded. In this case, do not use a ceramic capacitor whose series impedance is
low. Instead, use an electrolytic capacitor to suppress the inrush current and to prevent voltage rise.
13. VREG stabilization
To stabilize the V
REG
voltage that is the power supply for the control circuit, connect a 0.1μF or more capacitor
between V
REG
and GND. The capacitor GND must be wired near the GND pin of IC as much as possible.
No. 7107-16/17
LB11824M
相關PDF資料 |
PDF描述 |
|---|---|
| LB11824M | Direct PWM Drive Brushless Motor Predriver for On-Demand Water Heater and Air Conditioner Motors |
| LB11825M | LB11825M |
| LB11826 | LB11826 |
| LB11827 | Three-Phase Brushless Motor Driver for OA Products |
| LB11847 | PWM Current Control Type Stepping Motor Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB11824M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Direct PWM Drive Brushless Motor Predriver for On-Demand Water Heater and Air Conditioner Motors |
| LB11825M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:LB11825M |
| LB11826 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For OA Products Three-Phase Brushless Motor Driver |
| LB11826_08 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For OA Products Three-Phase Brushless Motor Driver |
| LB11826-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。