- 您現在的位置：買賣IC網 > PDF目錄358743 > LB11692JH (Sanyo Electric Co.,Ltd.) Monolithic Digital IC 24V Fan Motor Driver IC PDF資料下載
參數資料
| 型號： | LB11692JH |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Monolithic Digital IC 24V Fan Motor Driver IC |
| 中文描述： | 單片數字集成電路24V的風扇馬達驅動IC |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 129K |
| 代理商： | LB11692JH |
LB11692JH
No.A0333-9/12
LB11692JH Overview
1. Output Drive Circuit
The LB11692JH uses a direct PWM drive technique. Since the motor speed can be controlled by holding the supply
voltage constant and changing the output duty, the power supply design can be simplified compared to designs used
with techniques that vary the supply voltage (such as PAM drive). The low side output transistor is switched with a
pulse-width modulated signal and the drive output is adjusted by changing the duty. The LB11692JH includes built-
in output diodes for the regenerative currents that occur when the PWM signal is off and during phase switching.
2. Power Supply Stabilization
Since the LB11692JH uses a control method based on PWM switching, the power supply lines are susceptible to
disruption. Electrolytic capacitors with an adequate capacitance for stabilization must be connected between VCC
and ground. If diodes are inserted in the power supply lines to prevent destruction of the equipment if the power
supply is connected in reverse, the power supply lines will be particularly susceptible to disruption. In this case, even
larger capacitors must be used. The connected electrolytic capacitors must be located as close as possible to the IC
pins (VCC, VM, and GND2). If the electrolytic capacitors cannot be attached close to the pins due to problems with
the heat sink or other issues, ceramic capacitors of about 0.1μF must be attached close to the pins.
3. VREG Pin
At the same time as being the 5V regulator output, the VREG pin is also the power supply for the IC internal control
circuits. Therefore, a capacitor of at least 0.1μF must be connected between the VREG pin and ground to stabilize the
control circuit power supply. The ground side of the connected capacitor must be connected to the GND1 pin with as
short a line as possible.
4. FC Pin
The capacitor connected to the FC pin is required to correct the control loop's frequency characteristics.
(It should be about 0.1
μ
F.)
5. VD Pin
The VD pin supplies the low side output transistor drive current (a maximum of about 0.1A).
The IC internal power consumption is suppressed by connecting a resistor between the VCC and VD pins and
dividing power consumption due to the low side output transistor drive current with that resistor. Although the IC
internal power consumption due to the drive current can be reduced by lowering the VD pin voltage, a voltage of at
least 4V must be assured at the VD pin. Use a resistor in the range from about 50
(0.5W) to about 100
(1W)
between the VCC and VD pins when the LB11692JH is used with VCC = 24V.
6. Hall Effect Sensor Input Signals
Signals with amplitudes greater than 80mVp-p are required for the Hall effect sensor inputs. If possible, we
recommend providing signal amplitudes in excess of 100mVp-p to minimize the effects of noise. Add capacitors
across the Hall inputs (between the + and - sides of each input) if the output waveforms are disrupted by noise during
phase switching.
7. Current Limiter Circuit
The current limiter circuit limits the peak value of the output current to a current determined by the equation I =
VRF/Rf (where VRF = 0.5V (typical), Rf = current detection resistor value). When the limiter operates, it suppresses
the current by PWM control of the low side output transistor at the PWM frequency determined by the external
capacitor connected to the PWM pin, in particular, by reducing the on duty.
相關PDF資料 |
PDF描述 |
|---|---|
| LB11693H | Monolithic Digital IC 3-Phase Brushless Motor Driver for 24V Fan Motors |
| LB11693JH | Monolithic Digital IC 24V Fan Motor Driver IC |
| LB11696V | Direct PWM Drive Brushless Motor Predriver IC |
| LB11697V | Monolithic Digital IC Brushless Motor Driver IC |
| LB11817 | Three-Phase Full-Wave Linear Drive |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB11693 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Three-Phase Brushless Motor Driver for 24 V Fan Motors |
| LB11693H | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic Digital IC 3-Phase Brushless Motor Driver for 24V Fan Motors |
| LB11693H-MPB-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11693H-TLM-E | 功能描述:馬達/運動/點火控制器和驅動器 BRUSHLESS MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11693H-TRM-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。