參數資料
型號： LB11690
廠商： Sanyo Electric Co.,Ltd.
英文描述： Pre-Driver IC for Brushless Motor Drive in Electric Bicycles
中文描述： 預驅動器IC的電動自行車的無刷電機驅動
文件頁數： 14/19頁
文件大?。?/td> 201K
代理商： LB11690
6. Hall Sensor Input Signals
The outputs of the Hall sensor IC are connected to this IC's Hall sensor inputs. Since the IC includes internal pull-up
resistors (about 10 k
) to the 5 V regulator, normally, there is no need for external pull-up resistors. If a Hall sensor
IC with built-in pull-up resistors is used, no problems will occur as long as the Hall sensor IC uses a 5 V power
supply. However, pull-down resistors and voltage clamping
zener diodes must be added to assure that voltages over 5 V are
not applied to this IC if the Hall sensor IC uses a 12 V power
supply.
The inputs are comparator inputs with a hysteresis of about 0.9
V. If noise becomes a problem, noise rejection capacitors must
be inserted between the inputs and ground.
If all three of the Hall input signals go to the same input state, all
the outputs, both the high side and low side, will go to the off
state.
7. Undervoltage Protection Circuit
The undervoltage protection circuit detects the voltage applied to the LVS pin and if that voltage falls under the
operating voltage (3.8 V typical), the drive outputs are all set to the off state. This circuit has hysteresis to prevent the
circuit from repeatedly turning the outputs on and off when the supply voltage is close to the protection operating
voltage. Therefore, the output will not recover unless the supply voltage rises to about 0.5 V above the circuit's
operating voltage. Also, the RES pin voltage goes to the low level in the protection operating state.
The protection operating voltage is set to be the detection level
for a 5 V system. The detection level can be increased by
inserting a zener diode in the LVS pin to level shift the detection
level. (The detection voltage will then be the zener voltage (Vz)
plus 3.8 V (typical).) The LVS pin sink current during detection
is about 62 μA. If it is necessary to stabilize the zener diode
voltage increase and to minimize variations in the zener voltage,
insert a resistor between the LVS pin and ground to increase the
zener current. It is also possible to increase the detection voltage
without using a zener diode by using a resistor voltage divider.
If the circuit in the figure is used, the detection and release
voltages will be as follows.
Detection voltage
≈
((3.8 ÷ R2) + 62 μA)
×
(R1 + R2)
Release voltage
≈
((4.3 ÷ R2) + 70 μA)
×
(R1 + R2)
If R1 is 13 k
and R2 is 2.2 k
, the detection voltage will be
about 27 V and the release voltage will be about 31 V. Note that
errors in the detection voltage due to temperature and sample-to-sample variations increase as the value of the resistor
R2 increases.
If this protection circuit is not used, the LVS pin must not be left open (the outputs are turned off when this pin is
open). Rather, a voltage at a level at which the circuit does not operate must be applied.
8. RES Circuit
When power is first applied, the application must apply an initial reset to the RES pin to assure stable operation. The
initial reset performs the following operations.
All the drive outputs are turned off.
The EI
+
pin voltage is forced to the low level.
The FV pin voltage is forced to the low level.
Normally, a resistor and a capacitor are inserted between the RES pin and the V5 pin and the RES pin and ground,
respectively, to set the reset time. A resistor with a value of 2.7 k
or higher must be used. The time constant must be
set to a value such that R
×
C
≥
1 ms (if a 10 k
resistor is used, the capacitor must be 0.1 μF or larger). However, in
cases where it is necessary to completely discharge the capacitors on the EI
+
and FV pins, the reset time must be set to
cover those discharge times. It is also desirable to set the reset time to be longer than the time required to stabilize the
VB voltage after power is first applied.
No. 7543-14/19
LB11690, 11690H
Hall sensor IC
IN
LB11690,
11690H
12 V
5 V
To the detected power supply
LVS pin
Vz
To the detected power supply
LVS pin
R2
R1
Continued on next page.
相關PDF資料
PDF描述
LB11690H Pre-Driver IC for Brushless Motor Drive in Electric Bicycles
LB11691H Monolithic digital IC Pre-Driver IC for Brushless Motor Drive in Electric Bicycles
LB11691 Monolithic digital IC Pre-Driver IC for Brushless Motor Drive in Electric Bicycles
LB11692JH Monolithic Digital IC 24V Fan Motor Driver IC
LB11693H Monolithic Digital IC 3-Phase Brushless Motor Driver for 24V Fan Motors
相關代理商/技術參數
參數描述
LB11690H 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Pre-Driver IC for Brushless Motor Drive in Electric Bicycles
LB11691 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic digital IC Pre-Driver IC for Brushless Motor Drive in Electric Bicycles
LB11691H 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic digital IC Pre-Driver IC for Brushless Motor Drive in Electric Bicycles
LB11691H-TLM-E 制造商:Sony Semiconductor Solutions Division 功能描述:
LB11692JH 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic Digital IC 24V Fan Motor Driver IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*