參數資料
型號： KSZ8862-16MQL-FX
廠商： Micrel Inc
文件頁數： 55/125頁
文件大?。?/td> 0K
描述： IC SWITCH ETH 2P 16BIT 128PQFP
標準包裝： 66
系列： KSZ8862
控制器類型： 以太網開關控制器
接口： PCI
安裝類型： 表面貼裝
封裝/外殼： 128-BFQFP
供應商設備封裝： 128-PQFP（14x20）
包裝： 托盤
產品目錄頁面： 1081 (CN2011-ZH PDF)
配用： 576-1638-ND - BOARD EVALUATION KSZ8862-10FL
576-1637-ND - BOARD EVALUATION KSZ8862-100FX
其它名稱： 576-3271
Micrel, Inc.
KSZ8862-16/32MQL
April 2007
35
M9999-040407-3.0
Signal
Type
(1)
Function
RDYRTNN
I
Ready Return
For VLBus-like access: exactly like RDYRTNN signal in VLBus to end the cycle.
For burst access: exactly like EXRDY signal in EISA to insert wait states. Note that the
wait states are inserted by system logic (memory) not by KSZ8862M.
BCLK
I
Bus Clock
Asynchronous Transfer Signals
RDN
I
Asynchronous Read
WRN
I
Asynchronous Write
ARDY
O
Asynchronous Ready
This signal is asserted (low) to insert wait states.
Table 2. Bus Interface Unit Signal Grouping
Legend:
I = Input.
O = Output.
I/O = Bi-directional.
Regardless of whether the transfer is synchronous or asynchronous, if the address latch is required, use the rising edge of
ADSN to latch the incoming signals A[15:1], AEN, BE3N, BE2N, BE1N, and BE0N.
Note: Whether the transfer is synchronous or asynchronous, if the local device decoder is used, LDEVN will be asserted
to indicate that the KSZ8862M is successfully targeted. Basically, signal LDEVN is a combinatorial decode of AEN and
A[15:4].
Asynchronous Interface
For asynchronous transfers, the asynchronous dedicated signals RDN (for read) or WRN (for write) toggle, but the
synchronous dedicated signals BCLK, CYCLEN, SWR, and RDYRTNN are de-asserted and stay at the same logic level
throughout the entire asynchronous transfer.
There is no data burst support for asynchronous transfer. All asynchronous transfers are single-data transfers. The BIU,
however, provides flexible asynchronous interfacing to communicate with various applications and architectures. Three
major ways of interfacing with the system (host) are.
1.
Interfacing with the system/host relying on local device decoding and having stable address throughout the whole
transfer:
The typical example for this application is ISA-like bus interface using latched address signals as shown in the Figure
16. No additional address latch is required, therefore ADSN should be connected Low. The BIU decodes A[15:4] and
qualifies with AEN (Address Enable) to determine if the KSZ8862M switch is the intended target. The host utilizes the
rising edge of RDN to latch read data and the BIU will use rising edge of WRN to latch write data.
2.
Interfacing with the system/host relying on local device decoding but not having stable address throughout the entire
transfer: the typical example for this application is EISA-like bus (non-burst) interface as shown in the Figure 17. This
type of interface requires ADSN to latch the address on the rising edge. The BIU decodes latched A[15:4] and
qualifies with AEN to determine if the KSZ8862M switch is the intended target. The data transfer is the same as the
first case.
3.
Interfacing with the system/host relying on central decoding (KSZ8862-32 mode only).
The typical example for this application is for an embedded processor having a central decoder on the system board
or within the processor. Connecting the chip select (CS) from system/host to DATACSN bypasses the local device
decoder. When the DATACSN is asserted, it only allows access to the Data Register in 32 bits and BE3N, BE2N,
BE1N, and BE0N are ignored as shown in the Figure 18. No other registers can be accessed by asserting DATACSN.
The data transfer is the same as in the first case, independent of the type of asynchronous interface used. To insert a
wait state, the BIU will assert ARDY to prolong the cycle.
相關PDF資料
PDF描述
PIC16LF726-E/SO IC PIC MCU FLASH 8KX14 28-SOIC
0731010340 BNC JACK VERTICAL PCB 75 OHM
V300A5C400BF CONVERTER MOD DC/DC 5V 400W
V300A5C400BL3 CONVERTER MOD DC/DC 5V 400W
PIC16LC620A-04/SS IC MCU OTP 512X14 COMP 20SSOP
相關代理商/技術參數
參數描述
KSZ8862-32MQL 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (32-bit) bus interface. Fiber Capabilities on Port-1(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8862-32MQL-FX 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (32-bit) bus interface. Fiber Capabilities on Port-1(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8862-MQL 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with Non-PCI Interface and Fiber Support
KSZ8863FLL 功能描述:以太網 IC 3-Port 10/100 Ethernet Switch with 1x FX Port and 1x TX Port (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8863FLL-EVAL 功能描述:以太網開發工具 3-Port 10/100 Ethernet Switch with 1x FX Port and 1x TX Port - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*