- 您現在的位置：買賣IC網 > PDF目錄1931 > KSZ8001LI TR (Micrel Inc)IC TXRX PHY 10/100 3.3V 48LQFP PDF資料下載
參數資料
| 型號： | KSZ8001LI TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 2/46頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX PHY 10/100 3.3V 48LQFP |
| 標準包裝： | 1,000 |
| 類型： | 收發器 |
| 規程： | MII，RMII，SMII |
| 電源電壓： | 1.8V, 3.3V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 帶卷 (TR) |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
Micrel
KSZ8001
June 2009
Revision 1.04
10
Note 5:
MII Tx Mode: The TXD[3..0] bits are synchronous with TXCLK. When TXEN is asserted, TXD [3..0]
presents valid data from the MAC through the MII. TXD [3..0] has no effect when TXEN is de-asserted.
Note 6:
RMII Tx Mode: The TXD[1..0] bits are synchronous with REF_CLK. For each clock period in which TX_EN
is asserted, two bits of recovered data are recovered by the PHY.
Note 7:
SMII Tx Mode: Transmit data and control information are received in 10 bit segments. In 100MBit mode,
each segment represents a new byte of data. In 10MBit mode, each segment is repeated ten times;
therefore, every ten segments represents a new byte of data. The PHY can sample any one of every 10
segments in 10MBit mode.
Strapping Options
Pin Number
Pin Name
Type
(Note 2)
Description
6, 5, 4,
3
PHYAD[4:1] /
RXD[0:3]
Ipd/O
25
PHYAD0 /
INT#
Ipu/O
PHY Address latched at power-up / reset.
The default PHY address is 00001.
9
PCS_LPBK /
RXDV
Ipd/O
Enables PCS_LPBK mode at power-up / reset.
PD (default) = Disable, PU = Enable
10
SMII_SELECT
/ RXC
Ipd/O
Enables SMII mode at power-up / reset.
PD (default) = Disable, PU = Enable
11
ISO / RXER
Ipd/O
Enables ISOLATE mode at power-up /reset.
PD (default) = Disable, PU = Enable
21
RMII_SELECT
/ COL
Ipd/O
Enables RMII mode at power-up / reset.
PD (default) = Disable, PU = Enable
22
RMII_BTB/
CRS
Ipd/O
Enable RMII_BTB mode at power-up / reset.
PD (default) = Disable, PU = Enable
27
SPD100 /
No FEF /
LED1
Ipu/O
Latched into Register 0h bit 13 during power-up / reset.
PD = 10Mb/s, PU (default) = 100Mb/s.
If SPD100 is asserted during power-up / reset, this pin also
latched as the Speed Support in register 4h. (If FXEN is
pulled up, the latched value 0 means no Far _End _Fault.)
28
DUPLEX/
LED2
Ipu/O
Latched into Register 0h bit 8 during power-up / reset.
PD = Half Duplex, PU (default) = Full duplex.
If Duplex is pulled up during reset, this pin also latched as the
Duplex support in register 4h.
29
NWAYEN/
LED3
Ipu/O
Nway (auto-=Negotiation) Enable
Latched into Register 0h bit 12 during power-up / reset. PD =
Disable Auto-Negotiation, PU (default) = Enable Auto-
Negotiation
30
PD#
Ipu
Power Down Enable
PU (default) = Normal operation, PD = Power down mode
Note:
Strap-in is latched during power up or reset. In some systems, the MAC RXD pins may drive high at all times causing the
PHY strap-in to be latched high during power up or system reset. In this case, it is recommended to use a strong pull down to GND
via 1kohm resistor on RXDV, RXC, and RXER pins. Otherwise, the PHY may stay in Isolate or loop back modes.
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8031RNLI | TXRX PHY 10/100 3.3V 24-QFN |
| KSZ8041MLL TR | TXRX 10/100 3.3V PHY MII 48LQFP |
| KSZ8041NLA3TR | TRANSCEIVER 10/100 32-MLF |
| KSZ8041NLJ TR | TXRX PHY 10/100 3.3V 32MLF |
| KSZ8041RNL | TXRX 10/100 3.3V PHY RMII 32-MLF |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8001S | 功能描述:以太網 IC 10/100 BASE-TX/FX Physical Layer Transceiver with LinkMD cable diagnostics, Single 3.3V Supply, 48-SSOP, Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8001S TR | 功能描述:以太網 IC 10/100 BASE-TX/FX Physical Layer Transceiver with LinkMD cable diagnostics, Single 3.3V Supply, 48-SSOP, Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8001SA3 | 功能描述:TXRX 10/100 LINKMD 3.3V 48-SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND |
| KSZ8001SI | 功能描述:以太網 IC 10/100 BASE-TX/FX Physical Layer Transceiver with LinkMD cable diagnostics, Single 3.3V Supply, 48-LQFP, Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8001SL | 功能描述:以太網 IC 10/100 BASE-TX/FX Physical Layer Transceiver with LinkMD cable diagnostics, Single 3.3V Supply, 48-SSOP, Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。