參數資料
型號： ISL8489IB-T
廠商： INTERSIL CORP
元件分類： 通用總線功能
英文描述： 5V, Low Power, High Speed or Slew Rate Limited, RS-485/RS-422 Transceivers
中文描述： LINE TRANSCEIVER, PDSO14
封裝： PLASTIC, MS-012AB, SOIC-14
文件頁數： 7/16頁
文件大?。?/td> 507K
代理商： ISL8489IB-T
7
Receiver Disable from Output Low
t
LZ
C
L
= 15pF, SW = V
CC
, Figure 5
Full
-
10
50
ns
Maximum Data Rate
f
MAX
Full
250
-
-
kbps
Time to Shutdown (ISL8483 only)
t
SHDN
Note 7
Full
50
200
600
ns
Driver Enable from Shutdown to
Output High (ISL8483 only)
t
ZH(SHDN)
C
L
= 100pF, SW = GND, Figure 3, Notes 7, 8
Full
-
-
2000
ns
Driver Enable from Shutdown to
Output Low (ISL8483 only)
t
ZL(SHDN)
C
L
= 100pF, SW = V
CC
, Figure 3, Notes 7, 8
Full
-
-
2000
ns
Receiver Enable from Shutdown to
Output High (ISL8483 only)
t
ZH(SHDN)
C
L
= 15pF, SW = GND, Figure 5, Notes 7, 9
Full
-
-
2500
ns
Receiver Enable from Shutdown to
Output Low (ISL8483 only)
t
ZL(SHDN)
C
L
= 15pF, SW = V
CC
, Figure 5, Notes 7, 9
Full
-
-
2500
ns
NOTES:
2. All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless
otherwise specified.
3. Supply current specification is valid for loaded drivers when DE = 0V.
4. Applies to peak current. See “Typical Performance Curves” for more information.
5. When testing the ISL8483, keep RE = 0 to prevent the device from entering SHDN.
6. When testing the ISL8483, the RE signal high time must be short enough (typically <200ns) to prevent the device from entering SHDN.
7. The ISL8483 is put into shutdown by bringing RE high and DE low. If the inputs are in this state for less than 50ns, the parts are guaranteed not
to enter shutdown. If the inputs are in this state for at least 600ns, the parts are guaranteed to have entered shutdown. See “Low-Power
Shutdown Mode” section.
8. Keep RE = V
CC
, and set the DE signal low time >600ns to ensure that the device enters SHDN.
9. Set the RE signal high time >600ns to ensure that the device enters SHDN.
10. Devices meeting these limits are denoted as “single unit load (1 UL)” transceivers. The RS-485 standard allows up to 32 Unit Loads on the bus.
Test Circuits and Waveforms
FIGURE 1. DRIVER V
OD
AND V
OC
Electrical Specifications
Test Conditions: V
CC
= 4.5V to 5.5V; Unless Otherwise Specified.
Typicals are at V
CC
= 5V, T
A
= 25
o
C, Note 2
(Continued)
PARAMETER
SYMBOL
TEST CONDITIONS
TEMP
(
o
C)
MIN
TYP
MAX
UNITS
D
DE
DI
V
CC
V
OD
V
OC
R
R
Z
Y
ISL8483, ISL8485, ISL8488, ISL8489, ISL8490, ISL8491
相關PDF資料
PDF描述
ISL8489EIB +-15kV ESD Protected, 5V, Low Power, High Speed and Slew Rate Limited, Full Duplex, RS-485/RS-422 Transceivers
ISL8489EIB-T +-15kV ESD Protected, 5V, Low Power, High Speed and Slew Rate Limited, Full Duplex, RS-485/RS-422 Transceivers
ISL8489EIBZ +-15kV ESD Protected, 5V, Low Power, High Speed and Slew Rate Limited, Full Duplex, RS-485/RS-422 Transceivers
ISL8489EIBZ-T +-15kV ESD Protected, 5V, Low Power, High Speed and Slew Rate Limited, Full Duplex, RS-485/RS-422 Transceivers
ISL8563E +/-15kV ESD Protected, +3V to +5.5V, 1Microamp, 250kbps, EIA/TIA-562, EIA/TIA-232 Transmitters/Receivers
相關代理商/技術參數
參數描述
ISL8489IBZ 制造商:Intersil Corporation 功能描述:LINE TRNSCVR 1TR 1TX 1RX 14SOIC N - Rail/Tube
ISL8489IBZ-T 制造商:Intersil Corporation 功能描述:LINE TRNSCVR 1TR 1TX 1RX 14SOIC N - Tape and Reel
ISL8489IP 功能描述:RS-422/RS-485 接口 IC 5V TXRX RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube
ISL8490 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:5V, Low Power, High Speed or Slew Rate Limited, RS-485/RS-422 Transceivers
ISL8490E 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:【15kV ESD Protected, 5V, Low Power, High Speed and Slew Rate Limited, Full Duplex, RS-485/RS-422 Transceivers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*