- 您現在的位置：買賣IC網 > PDF目錄11423 > ISL76120ARTZ (Intersil)IC MULTIPLEXER DUAL SPDT 10TDFN PDF資料下載
參數資料
| 型號： | ISL76120ARTZ |
| 廠商： | Intersil |
| 文件頁數： | 13/13頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MULTIPLEXER DUAL SPDT 10TDFN |
| 標準包裝： | 100 |
| 功能： | 多路復用器 |
| 電路： | 2 x SPDT |
| 導通狀態電阻： | 10 歐姆 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 5.5 V |
| 電流 - 電源： | 20nA |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-VFDFN 裸露焊盤 |
| 供應商設備封裝： | 10-TDFN/MLP（3x3） |
| 包裝： | 管件 |
| 產品目錄頁面： | 1247 (CN2011-ZH PDF) |
9
FN6711.2
December 23, 2013
The maximum signal range for the HSx switches is from -1V
to VDD. The signal voltage should not be allow to exceed the
VDD voltage rail or go below ground by more than -1V.
The HSx switches are active (turned ON) whenever the IN
voltage is ≥1.4V and the EN logic voltage ≥1.4V when
operated with a 2.7V to 3.6V supply.
ISL76120 Operation
The discussion that follows will discuss using the ISL76120 in
the typical application shown in the“Application Block
POWER
The power supply connected at the VDD (pin 1) provides the
DC bias voltage required by the ISL76120 part for proper
operation. The ISL76120 can be operated with a VDD
voltage in the range of 2.7V to 5.5V. When used in a USB
application, the VDD voltage should be kept in the range of
3.0V to 5.5V to ensure you get the proper signal levels for
good signal quality.
A 0.01F or 0.1F decoupling capacitor should be
connected from the VDD pin to ground to filter out any power
supply noise from entering the part. The capacitor should be
located as close to the VDD pin as possible.
LOGIC CONTROL
The state of the ISL76120 device is determined by the
voltage at the IN pin (pin 2) and the EN pin (pin 10). IN is
only active when the EN pin is logic “1” (High). Refer to the
The EN pin is internally pulled low through a 4M
Ω resistor to
ground. For logic “0” (Low) it can be driven low or allowed to
Float. The IN pin must be driven low or high and cannot be
left floating.
Logic control voltage levels:
EN = Logic “0” (Low) when VEN ≤0.5V or Floating.
EN = Logic “1” (High) when VEN ≥1.4V
IN = Logic “0” (Low) when VIN ≤0.5V.
IN = Logic “1” (High) when VIN ≥1.4V
Full-speed Mode
If the IN pin = Logic “0” and the EN pin = Logic “1”, the part
will be in the full-speed mode. In this mode, the FSD1 and
FSD2 switches are ON and the HSD1 and HSD2 switches
are OFF (high impedance). In a typical application, VDD will
be in the range of 2.8V to 3.6V and will be connected to the
battery or LDO of the portable media device. When a
computer or USB hub is plugged into the common USB
connector and the part is in the full-speed mode, a link will
be established between the full-speed driver section of the
media player and the computer. The device will be able to
transmit and receive data from the computer at a data rate of
12Mbps.
High-speed Mode
If the IN pin = Logic “1” and the EN pin = Logic “1”, the part
will go into high-speed mode. In high-speed mode, the
HSD1 and HSD2 switches are ON and the FSD1 and FSD2
switches are OFF (high impedance). When a USB cable
from a computer or USB hub is connected at the common
USB connector and the part is in the high-speed mode, a link
will be established between the high-speed driver section of
the media player and the computer. The device will be able
to transmit and receive data from the computer at a data rate
of 480Mbps.
All Switches OFF Mode
If the IN pin = Logic “0” or Logic “1” and the EN pin = Logic “0”,
all of the switches will turn OFF (high impedance).
The all OFF state can be used to switch between the two
USB sections of the media player. When disconnecting from
one USB device to the other USB device, you can
momentarily put the ISL76120 switch in the “all off” state in
order to get the computer to disconnect from the one device
so it can properly connect to the other USB device when that
channel is turned ON.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B3Y-IW | CONVERTER MOD DC/DC 3.3V 66W |
| VI-23J-CV-F1 | CONVERTER MOD DC/DC 36V 150W |
| VI-23K-CV-F1 | CONVERTER MOD DC/DC 40V 150W |
| VE-B3Z-IX | CONVERTER MOD DC/DC 2V 30W |
| PI2PCIE2412ZHE | IC MUX/DEMUX 2X1 42TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL76120ARTZ-T | 功能描述:IC MULTIPLEXER DUAL SPDT 10TDFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL76120ARTZ-TR5303 | 制造商:Intersil Corporation 功能描述: |
| ISL76123 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Automotive Single Supply, SPDT Analog Switch |
| ISL76123AHZ-T | 制造商:Intersil Corporation 功能描述:ISL76123AHZ AUTOMOTIVE LOW-VOLTAGE,SINGLE SUPPLY,DUAL SPST,S - Tape and Reel 制造商:Intersil Corporation 功能描述:IC SWITCH AUTO SPDT SOT-23 制造商:Intersil 功能描述:Automotive LV Switch Dual SPST SPDT 3V |
| ISL76161 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:12-Bit, +3.3V, 130MSPS, High Speed D/A Converter |
發布緊急采購，3分鐘左右您將得到回復。