參數資料
型號： EVAL-ADAU1446EBZ
廠商： Analog Devices Inc
文件頁數： 21/92頁
文件大小： 0K
描述： BOARD EVAL FOR ADAU1446
標準包裝： 1
系列： SigmaDSP®
主要目的： 音頻，音頻處理
嵌入式： 是，DSP
已用 IC / 零件： ADAU1446
主要屬性： 單芯片多通道 28/56 位音頻 DSP
次要屬性： I²C & SPI 接口
已供物品： 板，軟件
ADAU1445/ADAU1446
Rev. A | Page 28 of 92
Self-Boot
On power-up, the ADAU1445/ADAU1446 can load a program
and a set of parameters that are saved in an external EEPROM.
Combined with the auxiliary ADC and the multipurpose pins,
this can potentially eliminate the need for a microcontroller in a
simple audio system. The self-boot sequence is accomplished by
the ADAU1445/ADAU1446 acting as masters on the I2C bus on
startup, which occurs when the SELFBOOT pin is set high. The
ADAU1445/ADAU1446 cannot self-boot in SPI mode.
The maximum necessary EEPROM size is 40,960 bytes, or
40 kB. This much memory is only needed if the program RAM
(4096 × 6 bytes) and parameter RAM (4096 × 4 bytes) are each
completely full.
A self-boot operation is triggered on the rising edge of RESET
when the SELFBOOT pin is set high, and it occurs after 10 ms
when the PLL has locked. The ADAU1445/ADAU1446 read the
program, parameter, and register data from the EEPROM. After
the ADAU1445/ADAU1446 have finished self-booting, additional
messages can be sent to the ADAU1445/ADAU1446 on the I2C
bus, although this typically is not necessary in a self-booting
application. The I2C device address for the ADAU1445/ADAU1446
is 0x68 for a write and 0x69 for a read in this mode. The ADDRx
pins have different functions when the chip is in this mode;
therefore, the settings on them are ignored.
The ADAU1445/ADAU1446 are masters on the I2C bus during
a self-boot operation. Care should be taken that no other device
on the I2C bus tries to perform a write operation during self-
booting. The ADAU1445/ADAU1446 generate SCL at 8 × fs;
therefore, when fs,NORMAL is 48 kHz, SCL runs at 384 kHz. SCL
has a duty cycle of in accordance with the I2C specification.
The ADAU1445/ADAU1446 read from EEPROM Chip Address
0xA1. The LSBs of the addresses of some EEPROMs are pin con-
figurable; in most cases, these pins should be tied low to set this
address. SigmaStudio writes to the EEPROM at Address 0xA0.
EEPROM Format
The EEPROM data contains a sequence of messages. Each
discrete message is one of the four types defined in Table 15.
Each message consists of a sequence of one or more bytes. The
first byte identifies the message type. Bytes are written MSB
first. Most messages are block write (0x01) types, which are
used for writing to the ADAU1445/ADAU1446 program RAM,
parameter RAM, and control registers.
The body of the message following the message type should
start with a byte indicating message length and then include a
byte indicating the chip address. Following this is always a
2-byte register or memory address field, as with all other
control port transactions.
SigmaStudio is capable of generating the EEPROM data necessary
to self-boot the ADAU1445/ADAU1446, using the function
called write latest compilation to E2PROM. This function can
be accessed by right-clicking the ADAU1445/ADAU1446 IC in
the hardware configuration window.
Table 14. Functions of the Control Port Pins
Pin
I2C Mode
SPI Mode
Self-Boot
SCL/CCLK
SCL—input
CCLK—input
SCL—output
SDA/COUT
SDA—open collector output
COUT—output
SDA—open collector output
ADDR1/CDATA
ADDR1—input
CDATA—input
Unused input—tie to ground or power
CLATCH
Unused input—tie to ground or power
CLATCH—input
Unused input—tie to ground or power
ADDR0
ADDR0—input
Unused input—tie to ground or power
Table 15. EEPROM Message Types
Message ID
Message Type
Following Bytes
0x00
End
None
0x01
Write
One byte indicating message length (including chip address and
subaddress), one byte indicating chip address, two bytes
indicating subaddress, and an appropriate number of data bytes
0x02
Delay
Two bytes for delay
0x03
No op
None
相關PDF資料
PDF描述
GEA22DTMT CONN EDGECARD 44POS R/A .125 SLD
EMC06DREH-S93 CONN EDGECARD 12POS .100 EYELET
LK2125R27M-T INDUCTOR MULTILAYER .27UH 0805
VE-204-EX CONVERTER MOD DC/DC 48V 75W
UMA1E330MDD CAP ALUM 33UF 25V 20% RADIAL
相關代理商/技術參數
參數描述
EVAL-ADAU1590EBZ 制造商:Analog Devices 功能描述:EVAL BOARD - Bulk
EVAL-ADAU1592EBZ 制造商:Analog Devices 功能描述:Evaluation Board For ADAU1592 制造商:Analog Devices 功能描述:EVAL BOARD - Boxed Product (Development Kits)
EVAL-ADAU1701EB 制造商:Analog Devices 功能描述:EVAL BOARD FOR SIGMADSP AUDIO PROCESSOR - Bulk
EVAL-ADAU1701EBZ 制造商:Analog Devices 功能描述:EVAL BOARD - Bulk
EVAL-ADAU1701MINIZ 功能描述:BOARD EVAL SIGMADSP AUD ADAU1701 RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:SigmaDSP® 產品培訓模塊:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色產品:Blackfin? BF50x Series Processors 標準包裝:1 系列:Blackfin® 類型:DSP 適用于相關產品:ADSP-BF548 所含物品:板，軟件，4x4 鍵盤，光學撥輪，QVGA 觸摸屏 LCD 和 40G 硬盤 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相關產品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*