- 您現在的位置：買賣IC網 > PDF目錄381802 > EN29F002AT-90TCP (Electronic Theatre Controls, Inc.) 2 Megabit (256K x 8-bit) Flash Memory PDF資料下載
參數資料
| 型號： | EN29F002AT-90TCP |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 2 Megabit (256K x 8-bit) Flash Memory |
| 中文描述： | 2兆位（256K × 8位）閃存 |
| 文件頁數： | 11/35頁 |
| 文件大?。?/td> | 431K |
| 代理商： | EN29F002AT-90TCP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
This Data Sheet may be revised by subsequent versions 2003 Eon Silicon Solution, Inc., www.essi.com.tw
or modifications due to changes in technical specifications.
Rev. A, Issue Date: 2003/03/26
EN29F002A / EN29F002AN
The flowchart for the Toggle Bit (DQ6) is shown in Flowchart 6. The Toggle Bit timing diagram is
shown in Figure 9
.
DQ5
Exceeded Timing Limits
DQ5 will indicate if the program or erase time has exceeded the specified limits (internal pulse
count). Under these conditions DQ5 will produce a “1”. (The Toggle Bit (DQ6) should also be
checked at this time to make sure that the DQ5 is not a “1” due to the device having returned to read
mode.) This is a failure condition which indicates that the program or erase cycle was not
successfully completed.
DATA
Polling (DQ7), Toggle Bit (DQ6) and Erase Toggle Bit (DQ2) still
function under this condition. Setting the
CE
to V
IH
will partially power down the device under those
conditions. The
OE
and
WE
pins will control the output disable functions as described in Table 3.
The DQ5 failure condition will also appear if the user tries to program a “1” to a location that was
previously programmed to a “0”. In this case, the device goes into Hang or Error mode out and
never completes the Embedded Program Algorithm. Hence, the system never reads valid data on
DQ7 and DQ6 never stops toggling. Once the device exceeds the timing limits, DQ5 will indicate a
“1”. Please note that this is not a device failure condition since the device was used incorrectly. If
timing limits are exceeded, reset the device. (See Table 6)
DQ3
Sector Erase Command Timeout
This device does not support multiple sector erase commands. DQ3 will go high immediately after
the first 30h command (the sixth write cycle). Any extra 30h commands will be ignored (or taken as
a resume command if erase suspended).
DQ2
Erase Toggle Bit II
In the sector erase operation, DQ2 will toggle with
OE
or
CE
when a read is attempted within the
sector that is being erased. DQ2 will not toggle if the read address is not within the sector that is
selected to be erased. In the chip erase operation, however, DQ2 will toggle with
OE
or
CE
regardless of the address given by the user. This is because all sectors are to be erased. (See
Table 6)
相關PDF資料 |
PDF描述 |
|---|---|
| EN29F002AT-90TI | 2 Megabit (256K x 8-bit) Flash Memory |
| EN29F002AT-90TIP | 2 Megabit (256K x 8-bit) Flash Memory |
| EN29F002AT-70TC | 2 Megabit (256K x 8-bit) Flash Memory |
| EN29F002T-55J | Octal D Flip-Flop with 3-STATE Outputs; Package: TSSOP; No of Pins: 20; Container: Rail |
| EN29F002 | 2 Megabit (256K x 8-bit) Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EN29F002AT-90TI | 制造商:EON 制造商全稱:Eon Silicon Solution Inc. 功能描述:2 Megabit (256K x 8-bit) Flash Memory |
| EN29F002AT-90TIP | 制造商:EON 制造商全稱:Eon Silicon Solution Inc. 功能描述:2 Megabit (256K x 8-bit) Flash Memory |
| EN29F002B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2 Megabit (262，144 x 8) FLASH |
| EN29F002B-45J | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2 Megabit (256K x 8-bit) Flash Memory |
| EN29F002B-45JI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2 Megabit (256K x 8-bit) Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。