參數資料
型號: EM78P5830AAM
廠商: ELAN Microelctronics Corp .
英文描述: 8-BIT MICRO-CONTROLLER
中文描述: 8位微控制器
文件頁數: 9/43頁
文件大小: 396K
代理商: EM78P5830AAM
EM785830AA
8-bit Micro-controller
__________________________________________________________________________________________________________________________________________________________________
* This specification is subject to be changed without notice.
12/1/2004 V1.6
0E
0F Interrupt mask
10
:
1F
20
:
3F
VII.2 Operational Register Detail Description
R0 (Indirect Addressing Register)
R0 is not a physically implemented register. It is used as indirect addressing pointer. Any instruction using R0
as register actually accesses data pointed by the RAM Select Register (R4).
Example:
Mov
A, @0x20
;store a address at R4 for indirect addressing
Mov
0x04, A
Mov
A, @0xAA
;write data 0xAA to R20 at bank0 through R0
Mov
0x00, A
R1 (TCC)
TCC data buffer. Increased by 16.384KHz or by the instruction cycle clock (controlled by CONT register).
Written and read by the program as any other register.
R2 (Program Counter)
The structure is depicted in Fig.3.
Generates 16k
×
13 on-chip ROM addresses to the relative programming instruction codes.
"JMP" instruction allows the direct loading of the low 10 program counter bits.
"CALL" instruction loads the low 10 bits of the PC, PC+1, and then push into the stack.
"RET'' ("RETL k", "RETI") instruction loads the program counter with the contents at the top of stack.
"MOV R2, A" allows the loading of an address from the A register to the PC, and the ninth and tenth bits are
cleared to "0''.
"ADD R2,A" allows a relative address be added to the current PC, and contents of the ninth and tenth bits are
cleared to "0''.
"TBL" allows a relative address added to the current PC, and contents of the ninth and tenth bits don't change.
The most significant bit (A10~A11) will be loaded with the contents of bit PS0~PS1 in the status register (R5
PAGE0) upon the execution of a "JMP'', "CALL'', "ADD R2, A'', or "MOV R2, A'' instruction.
If an interrupt is triggered, PROGRAM ROM will jump to address 0x08 at page0. The CPU will store ACC,
R3 status and R5 PAGE automatically, and they will be restored after instruction RETI.
相關PDF資料
PDF描述
EM78P5830AAP 8-BIT MICRO-CONTROLLER
EM78P5830ADQ 8-BIT MICRO-CONTROLLER
EM78P5830AM 8-BIT MICRO-CONTROLLER
EM78P5830AP 8-BIT MICRO-CONTROLLER
EM78P5830DQ 8-BIT MICRO-CONTROLLER
相關代理商/技術參數
參數描述
EM7A8620 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:Voice over IP
EM7G 制造商:GULFSEMI 制造商全稱:Gulf Semiconductor 功能描述:ULTRAFAST EFFICIENT PLASTIC SILICON RECTIFIER VOLTAGE: 1000V CURRENT: 1.0A
EM800 制造商:EDI 制造商全稱:Electronic devices inc. 功能描述:HIGH VOLTAGE HIGH CURRENT MINIATURE RECTIFIERS
EM8000EHP 制造商:JDSU 制造商全稱:JDS Uniphase Corporation 功能描述:The industrya??s most compact 100 G test solution
EM800-DCM 制造商:MRV 制造商全稱:MRV 功能描述:LambdaDriver Dispersion Compensation Module (EM800/1600-DCM and DCMD)