- 您現在的位置：買賣IC網 > PDF目錄11560 > DS3148N (Maxim Integrated Products)IC 8CH DS3/3 FRAMER 349-BGA PDF資料下載
參數資料
| 型號： | DS3148N |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 66/89頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC 8CH DS3/3 FRAMER 349-BGA |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 控制器類型： | DS3/E3 調幀器 |
| 接口： | LIU |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 電流 - 電源： | 640mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 349-BGA 裸露焊盤 |
| 供應商設備封裝： | 349-HCBGA（27x27） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁當前第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁
DS3146/DS3146/DS31412 6-/8-/12-Channel DS3/E3 Framers
69 of 89
8.4 Loopback Modes
The loopback modes are selected by setting the LLB, DLB, and/or PLB bits in the MC2 register. See Figure 1-1 for
a visual description of these loopbacks. At reset, none of the loopback modes are activated. PLB and DLB may not
be active at the same time. If LLB and PLB are both active at the same time, then TPOS/TNRZ, TNEG, and TCLK
are sourced from RPOS/RNRZ, RNEG/RLCV, and RCLK while the internal workings of the framer are in PLB
mode.
The line loopback (LLB) mode is used to send the received signal back toward the network. TAIS and TUA1 are
not available during line loopback, but the TPOS/TRNZ and TNEG pins can be forced high and low using the
TPOSH, TPOSI, TNEGH, and TNEGI bits in the MC5 register.
The diagnostic loopback (DLB) mode is used to send the transmitted signal back toward the system through the
receive framer. When the framer is in diagnostic loopback, it can simultaneously transmit AIS to the far end if the
TAIS bit is set in the T3E3CR1 register. The framer supports simultaneous line loopback and diagnostic loopback.
The payload loopback (PLB) mode is used to send the received payload back toward the network with new
overhead inserted. When the framer is in payload loopback, the internal transmit clock is connected to the internal
receive clock, internal transmit data is sourced from internal receive data, and TICLK and TDAT are ignored. The
TDEN and TSOF signals are aligned with the RDEN and RSOF signals, and TOH and TOHEN are still enabled.
The TSOF, TDEN, TOH, and TOHEN signals are timed relative to ROCLK rather than TICLK.
8.5 Transmit Overhead Insertion
The transmit signal can be overwritten at any bit location using the TOH and TOHEN signals. The TSOF signal
marks the start of the transmit frame and is used to determine which bits to overwrite. To overwrite a specific bit in
the DS3 or E3 frame, count the required number of TICLK cycles after the TSOF frame pulse. When the proper
TICLK cycle is reached, assert the TOHEN pin to replace normal transmit data (overhead or payload) with the
value on the TOH pin. One application for the TOH and TOHEN pins is to use some of the unused C bits in DS3 C-
Bit Parity mode for a proprietary communications channel.
During payload loopback, the transmit side is timed from ROCLK rather than TICLK. If the system needs to support
transmit overhead insertion (TOH) during payload loopback (PLB), then TOH and TOHEN must also be timed with
respect to ROCLK. One way to access ROCLK is to set the TCCLK bit in the MC2 register to convert the
TDEN/TGCLK output pin into a constant clock, which is based on ROCLK during payload loopback. TOH and
TOHEN can then be timed with respect to the constant clock on the TDEN/TGCLK pin.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-24K-IX-S | CONVERTER MOD DC/DC 40V 75W |
| PIC16C54C-20E/SO | IC MCU OTP 512X12 18SOIC |
| PIC16C54C-04E/SS | IC MCU OTP 512X12 20SSOP |
| PIC12C509T-04/SM | IC MCU OTP 1KX12 8-SOIJ |
| PIC12C508T-04I/SM | IC MCU OTP 512X12 8-SOIJ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS315 | 制造商:Hubbell Wiring Device-Kellems 功能描述:SWITCH, DECO SER, 3W, 15A 120/277V, BR |
| DS3150 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:3.3V, DS3/E3/STS-1 Line Interface Unit |
| DS3150DK | 功能描述:網絡開發工具 DS3150 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V |
| DS3150G | 功能描述:IC LIU T3/E3/STS-1 49-BGA RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 供應商設備封裝:16-PDIP 包裝:管件 |
| DS3150GN | 功能描述:IC LIU T3/E3/STS-1 IND 49-BGA RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 供應商設備封裝:16-PDIP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。