參數資料
型號： DS3112D1+
廠商： Maxim Integrated Products
文件頁數： 63/133頁
文件大?。?/td> 0K
描述： IC MUX T3/E3 3.3V 256-PBGA
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 40
控制器類型： 調幀器，多路復用器
接口： 并行/串行
電源電壓： 3.135 V ~ 3.465 V
電流 - 電源： 150mA
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 256-LBGA
供應商設備封裝： 256-PBGA（27x27）
包裝： 管件
DS3112
35 of 133
Bit 4: Manual Error Counter Update (MECU). A zero to one transition on this bit will cause the device to
update the performance error counters. This bit is ignored if the AECU control bit is set low. This bit must be
cleared and set again for a subsequent update. This bit is logically ORed with the external FRMECU hardware
input signal. After this bit has toggled, the host must wait at least 100ns before reading the error counters to allow
the device time to complete the update.
Bit 5: High-Speed (T3/E3) Port Unipolar Enable (UNI). When this bit is set low, the device will output a bipolar
coded signal at HTPOS and HTNEG and expect a bipolar coded signal at HRPOS and HRNEG. When this bit is
set high, the device will output a NRZ coded signal at HTPOS and expect a NRZ coded signal at HRPOS. In the
unipolar mode, the device will force the HTNEG output low and the HRNEG input is ignored and should be tied
low. In the unipolar mode, the B3ZS and HDB3 coder/decoders should be disabled by setting the ZCSD bit to one
(ZCSD = 1).
0 = bipolar mode
1 = unipolar mode
Bit 6: Loss Of Transmit Clock Mux Control (LOTCMC). The DS3112 can detect if the FTCLK fails to
transition. If this bit is set low, the device will take no action (other than setting the LOTC status bit) when the
FTCLK fails to transition. When this bit is set high, the device will automatically switch to the input receive clock
(HRCLK) when the FTCLK fails and transmit AIS.
0 = do not switch to the HRCLK signal if FTCLK fails to transition
1 = automatically switch to the HRCLK signal if the FTCLK fails to transition and send AIS
Bit 7: T3/E3 Transmit Frame Sync I/O Control (FTSOFC). When this bit is set low, the FTSOF signal will be
an output and will pulse for one FTCLK cycle at the beginning of each frame. When this bit is high, the FTSOF
signal is an input and the device uses it to determine the frame boundaries.
0 = FTSOF is an output
1 = FTSOF is an input
Bit 8: Low-Speed (T1/E1) Transmit Port Common Clock Enable (LTCCEN). When this bit is set high, the
LTCLK1 to LTCLK28 and LTCLKA and LTCLKB inputs are ignored and a common clock sourced via the
LTCCLK input is used in their place.
0 = disable LTCCLK
1 = enable LTCCLK
Bit 9: Low-Speed (T1/E1) Receive Port Common Clock Enable (LRCCEN). When this bit is set high, the
LRCLK1 to LRCLK28 and LRCLKA and LRCLKB outputs will all be sourced from the LRCCLK input. This
configuration can only be used in applications where it can be insured that all of the T1 or E1 channels from the far
end are being sourced from a common clock.
0 = disable LRCCLK
1 = enable LRCCLK
Bit 10: High-Speed (T3/E3) Data Enable Mode Select (DENMS). When this bit is set low, the FRDEN and
FTDEN outputs will be asserted during payload data and deasserted during overhead data. When this bit is high,
FRDEN and FTDEN are gapped clocks that pulse during payload data and are suppressed during overhead data.
0 = FRDEN and FTDEN are data enables
1 = FRDEN and FTDEN are gapped clocks
Bit 11: Low-Speed (T1/E1) Port Loop Timed Mode (LLTM). When this bit is set low, the low-speed T1 and E1
receive clocks (LRCLK) are not routed to the transmit side. When this bit is high, the LRCLKs are routed to the
transmit side to be used as the transmit T1 and E1 clocks. When enabled, all the low-speed ports are looped timed.
This control bit affects all the low-speed ports. The device is not capable of setting individual low-speed ports into
and out of looped timed mode. See the block diagram in Figure 1-1 and Figure 1-2 for more details.
0 = disable loop timed mode (LRCLK is not used to replace the associated LTCLK)
1 = enable loop timed mode (LRCLK replaces the associated LTCLK)
相關PDF資料
PDF描述
413959-6 CONN PLUG BNC RG141 R/A CRIMP AU
VE-BTZ-IV-S CONVERTER MOD DC/DC 2V 60W
VE-BTY-IV-S CONVERTER MOD DC/DC 3.3V 99W
227079-3 CONN PLUG BNC RG59,62 CRIMP TIN
VE-2T1-IX-S CONVERTER MOD DC/DC 12V 75W
相關代理商/技術參數
參數描述
DS3112D1+ 功能描述:網絡控制器與處理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS3112DK 功能描述:網絡開發工具 DS3112 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
DS3112N 功能描述:網絡控制器與處理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS3112N+ 功能描述:網絡控制器與處理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS3112N+W 功能描述:網絡控制器與處理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*