- 您現在的位置：買賣IC網 > PDF目錄376964 > DS2152L Enhanced T1 Single-Chip Transceiver PDF資料下載
參數資料
| 型號： | DS2152L |
| 英文描述： | Enhanced T1 Single-Chip Transceiver |
| 中文描述： | 增強型T1單芯片收發器 |
| 文件頁數： | 29/94頁 |
| 文件大小： | 1003K |
| 代理商： | DS2152L |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁
DS2152
29 of 93
CCR7: COMMON CONTROL REGISTER 7
(Address=0A Hex)
(MSB) (LSB)
LIRST
RLB
-
-
-
-
-
-
SYMBOL
POSITION
NAME AND DESCRIPTION
LIRST
CCR7.7
Line Interface reset.
Setting this bit from a 0 to a 1 will initiate
an internal reset that affects the clock recovery state machine and
jitter attenuator. Normally this bit is only toggled on power-up.
Must be cleared and set again for a subsequent reset.
RLB
CCR7.6
Remote Loopback.
0 = loopback disabled
1 = loopback enabled
-
CCR7.5
Not Assigned.
Should be set to 0 when written to.
-
CCR7.4
Not Assigned.
Should be set to 0 when written to.
-
CCR7.3
Not Assigned.
Should be set to 0 when written to.
-
CCR7.2
Not Assigned.
Should be set to 0 when written to.
-
CCR7.1
Not Assigned.
Should be set to 0 when written to.
-
CCR7.0
Not Assigned.
Should be set to 0 when written to.
Power-Up Sequence
On power-up, after the supplies are stable, the DS2152 should be configured for operation by writing to
all of the internal registers (this includes setting the Test Registers to 00Hex) since the contents of the
internal registers cannot be predicted on power-up. Finally, after the TSYSCLK and RSYSCLK inputs
are stable, the ESR bit should be toggled from a 0 to a 1 (this step can be skipped if the elastic stores are
disabled).
Remote Loopback
When CCR7.6 is set to a 1, the DS2152 will be forced into Remote LoopBack (RLB). In this loopback,
data input via the RPOSI and RNEGI pins will be transmitted back to the TPOSO and TNEGO pins. Data
will continue to pass through the receive side framer of the DS2152 as it would normally and the data
from the transmit side formatter will be ignored. Please see Figure 1-1 for more details.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2152 | Enhanced T1 Single-Chip Transceiver |
| DS2160Q | Data Encryption Processor |
| DS2160QN | Peripheral IC |
| DS2165QL | Solid-State Recorder |
| DS2165QN | Solid-State Recorder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2152L+ | 功能描述:網絡控制器與處理器 IC Enhanced T1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2152L-ES | 制造商:DALL 功能描述: |
| DS2152LN | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2152LN+ | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2153DK | 功能描述:KIT DESIGN TXRX E1 DS2153 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
發布緊急采購，3分鐘左右您將得到回復。