參數資料
型號： DS2152L
英文描述： Enhanced T1 Single-Chip Transceiver
中文描述： 增強型T1單芯片收發器
文件頁數： 25/94頁
文件大小： 1003K
代理商： DS2152L
DS2152
25 of 93
CCR3: COMMON CONTROL REGISTER 3
(Address=30 Hex)
(MSB) (LSB)
ESMDM
ESR
RLOSF
RSMS
PDE
ECUS
TLOOP
-
SYMBOL
ESMDM
POSITION
CCR3.7
NAME AND DESCRIPTION
Elastic Store Minimum Delay Mode.
See Section 10.3 for
details.
0 = elastic stores operate at full two-frame depth
1 = elastic stores operate at 32-bit depth
Elastic Store Reset.
Setting this bit from a 0 to a 1 will force the
elastic stores to a known depth. Should be toggled after
RSYSCLK and TSYSCLK have been applied and are stable.
Must be cleared and set again for a subsequent reset.
Function of the RLOS/LOTC Output.
0 = Receive Loss of Sync (RLOS)
1 = Loss of Transmit Clock (LOTC)
RSYNC Multiframe Skip Control.
Useful in framing format
conversions from D4 to ESF. This function is not available when
the receive side elastic store is enabled.
0 = RSYNC will output a pulse at every multiframe
1 = RSYNC will output a pulse at every other multiframe
note: for this bit to have any affect, the RSYNC must be set to
output multiframe pulses (RCR2.4=1 and RCR2.3=0).
Pulse Density Enforcer Enable.
0 = disable transmit pulse density enforcer
1 = enable transmit pulse density enforcer
Error Counter Update Select.
See Section 5 for details.
0 = update error counters once a second
1 = update error counters every 42 ms (333 frames)
Transmit Loop Code Enable.
See Section 12 for details.
0 = transmit data normally
1 = replace normal transmitted data with repeating code as
defined in TCD register
Not Assigned.
Must be set to 0 when written.
ESR
CCR3.6
RLOSF
CCR3.5
RSMS
CCR3.4
PDE
CCR3.3
ECUS
CCR3.2
TLOOP
CCR3.1
-
CCR3.0
Pulse Density Enforcer
The SCT always examines both the transmit and receive data streams for violations of the following rules
which are required by ANSI T1.403:
-
no more than 15 consecutive 0s
-
at least N 1s in each and every time window of 8 x (N +1) bits where N = 1 through 23
Violations for the transmit and receive data streams are reported in the RIR2.0 and RIR2.1 bits
respectively. When the CCR3.3 is set to 1, the DS2152 will force the transmitted stream to meet this
requirement no matter the content of the transmitted stream. When running B8ZS, the CCR3.3 bit should
be set to 0 since B8ZS encoded data streams cannot violate the pulse density requirements.
相關PDF資料
PDF描述
DS2152 Enhanced T1 Single-Chip Transceiver
DS2160Q Data Encryption Processor
DS2160QN Peripheral IC
DS2165QL Solid-State Recorder
DS2165QN Solid-State Recorder
相關代理商/技術參數
參數描述
DS2152L+ 功能描述:網絡控制器與處理器 IC Enhanced T1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2152L-ES 制造商:DALL 功能描述:
DS2152LN 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2152LN+ 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2153DK 功能描述:KIT DESIGN TXRX E1 DS2153 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*