- 您現在的位置：買賣IC網 > PDF目錄379929 > COP688CL (National Semiconductor Corporation) 8-Bit Microcontroller(8位微控制器) PDF資料下載
參數資料
| 型號： | COP688CL |
| 廠商： | National Semiconductor Corporation |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-Bit Microcontroller(8位微控制器) |
| 中文描述： | 8位微控制器（8位微控制器） |
| 文件頁數： | 27/41頁 |
| 文件大?。?/td> | 565K |
| 代理商： | COP688CL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
MICROWIRE/PLUS
(Continued)
MICROWIRE/PLUS Slave Mode Operation
In the MICROWIRE/PLUS Slave mode of operation the SK
clock is generated by an external source. Setting the MSEL
bit in the CNTRL register enables the SO and SK functions
onto the G Port. The SK pin must be selected as an input
and the SO pin is selected as an output pin by setting and
resetting the appropriate bit in the Port G configuration reg-
ister. Table V summarizes the settings required to enter the
Slave mode of operation.
The user must set the BUSY flag immediately upon entering
the Slave mode. This will ensure that all data bits sent by the
Master will be shifted properly. After eight clock pulses the
BUSY flag will be cleared and the sequence may be re-
peated.
Alternate SK Phase Operation
The device allows either the normal SK clock or an alternate
phase SK clock to shift data in and out of the SIO register. In
both the modes the SK is normally low. In the normal mode
data is shifted in on the rising edge of the SK clock and the
data is shifted out on the falling edge of the SK clock. The
SIO register is shifted on each falling edge of the SK clock.
In the alternate SK phase operation, data is shifted in on the
falling edge of the SK clock and shifted out on the rising edge
of the SK clock.
A control flag, SKSEL, allows either the normal SK clock or
the alternate SK clock to be selected. Resetting SKSEL
causes the MICROWIRE/PLUS logic to be clocked from the
normal SK signal. Setting the SKSEL flag selects the alter-
nate SK clock. The SKSEL is mapped into the G6 configu-
ration bit. The SKSEL flag will power up in the reset condi-
tion, selecting the normal SK signal.
This table assumes that the control flag MSEL is set.
TABLE 7.
G4
(SO)
Config.
Bit
1
G5
(SK)
Config.
Bit
1
G4
Fun.
G5
Fun.
Operation
SO
Int.
SK
Int.
SK
Ext.
SK
Ext.
SK
MICROWIRE/PLUS
Master
MICROWIRE/PLUS
Master
MICROWIRE/PLUS
Slave
MICROWIRE/PLUS
Slave
0
1
TRI-
STATE
SO
1
0
0
0
TRI-
STATE
DS009766-21
FIGURE 14. MICROWIRE/PLUS Application
C
www.national.com
27
相關PDF資料 |
PDF描述 |
|---|---|
| COP888CL | 8-Bit Microcontroller(8位微控制器) |
| COP988CL | 8-Bit Microcontroller(8位微控制器) |
| COP684CL | 8-Bit Microcontroller(8位微控制器) |
| COP884CL | 8-Bit Microcontroller(8位微控制器) |
| COP984CL | 8-Bit Microcontroller(8位微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| COP688CL-XXX/N | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:General Description |
| COP688CL-XXX/V | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:General Description |
| COP688CS | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS ROM Based Microcontrollers with 4k to 24k Memory, Comparators and USART |
| COP688CS-XXX/V | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|COP800 CPU|CMOS|LDCC|44PIN|PLASTIC |
| COP688EB | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS ROM Based Microcontrollers with 8k Memory, CAN Interface, 8-Bit A/D, and USART |
發布緊急采購，3分鐘左右您將得到回復。