通知：奧松機器人科技有限公司于2013年正式成為美國Pololu官方授權中國區域代理商，此款產品為國內首發，火熱搶購中，由于數量有限，拍下時請咨詢客服是否有庫存。
 

 
USB AVR編程器 Arduino下載器 3Pi Robot下載器 Pololu 原裝進口
 
 

 
     這是一款非常簡潔且易用的USB 編程器，該裝置基于Atmel AVR控制器，使得我們的3Pi Robot操作更加方便。除此之外他還具備模擬STK500的虛擬串口，兼容標準AVR編程軟件。這兩個額外的功能，可以幫助我們構建和調試TTL串行端口用于通用的溝通和SLO-監測信號及電壓等級范圍等項目。此款產品支持Windows XP, Windows Vista, Windows 7, Windows 8, and Linux等操作系統。
 

 
Pololu 原裝進口 細節展示
 
產品特點：
1、產品名稱：Pololu USB AVR下載器

2、產品貨號：RB-03T037

3、一般的AVR ISP 編程：基于 Atmel AVR 控制器，可通過USB端口與電腦連接，通過附帶的USB A到mini-B電纜和通信編程軟件，如Atmel Studio或AVRDUDE，通過一個虛擬的COM端口使用AVRISPV2/STK500協議。

4、操作系統： Windows XP, Windows Vista, Windows 7, Windows 8, and Linux

5、TTL串行端口：USB AVR編程作為一個編程器安裝兩個虛擬COM端口的USB到串口適配器：一個用于通信的編程軟件和一個通用USB到串口適配器，這意味著通過TTL串口你可以任意地切換一個AVR編程和調試，而無需打開和關閉終端程序。

6、SLO-scope：此裝置還可以應用于另外兩個渠道。嚴重限制的示波器（ SLO范圍）用A和B引腳為模擬電壓輸入和的Pololu SLO范圍為Windows應用程序的SLO范圍可以測量電壓在0 ～ 5 V （最大電壓由USB電壓的控制） 。如果你使用外部分壓器，它支持兩種采樣模式： 10 kHz的兩個8位模擬輸入7位或20 kHz的模擬輸入和數字輸入，這個功能可以幫助您調試您的電路和固件。

 


 
電子元件 清晰標注
 
 

 
實物比對 尺寸準確
 
注意：此編程器支持標準系統編程（ISP），有時也被稱為在線串行編程（ICSP）。不支持JTAG，debugWIRE的，或高電壓編程。
 
推薦搭配：

Pololu 3pi Robot 輪式機器人
 
General AVR ISP Programmer 

The Pololu USB AVR Programmer is an extremely compact, low-cost in-system programmer (ISP) for Atmel’s AVR mirocontrollers, which makes this device an attractive programming solution for AVR-based controllers like Pololu Orangutan robot controllers. The USB AVR programmer connects to your computer’s USB port via an included USB A to mini-B cable and communicates with your programming software, such as Atmel Studio or AVRDUDE, through a virtual COM port using the AVRISPV2/STK500 protocol. The programmer connects to your target device via an included 6-pin ISP programming cable (the older, 10-pin ISP connections are not directly supported, but it’s easy to create or purchase a 6-pin-to-10-pin ISP adapter). 

 

Supported Microcontrollers

The programmer should work with all AVRs that can be programmed with the AVR ISP interface, but it has not been tested on all devices. It has been tested with all Orangutan robot controllers and the 3pi Robot. The programmer features upgradable firmware, allowing updates for future devices. It does not currently work with Atmel’s XMega line of microcontrollers.

The programmer is powered by the 5V USB power bus, and it is intended for programming AVRs that are running at close to 5 V (note that the programmer does not deliver power to the target device).

 

Supported Operating Systems

The programmer has been tested under Windows XP, Windows Vista, Windows 7, Windows 8, and Linux. We provide limited support for using this programmer on Mac OS X; please see the user’s guide for details. This programmer is not compatible with older versions of Windows.

 

Bonus Feature: TTL-level serial port

The USB AVR programmer doubles as a USB-to-serial adapter. The programmer installs as two virtual COM ports: one for communicating with programming software and one for the general-purpose USB-to-serial adapter. This means that you can seamlessly switch between programming an AVR and debugging it through the TTL serial port without having to open and close your terminal program. In addition to the serial transmit (TX), and receive (RX), lines, the programmer lets you use pins A and B as serial handshaking lines. The programmer’s configuration utility allows you to select which handshaking line is assigned to which pin, and both input and output handshaking lines are supported. The programmer also gives you access to the USB’s regulated 5V power bus through the VBUS pin. The TTL-level serial port is not supported in Mac OS. 

 

Bonus Feature: SLO-scope

This device can also act as a two-channel, severely limited oscilloscope (SLO-scope) using the A and B pins as analog voltage inputs and the Pololu SLO-scope application for Windows. The SLO-scope can measure voltages between 0 and ~5 V (the maximum is limited by the USB bus voltage), or higher if you use an external voltage divider, and it supports two sampling modes: 10 kHz sampling of two 8-bit analog inputs or 20 kHz sampling of one 7-bit analog input and one digital input. This feature can help you debug your circuits and firmware by seeing what the voltages are doing at various nodes. (Please note that the SLO-scope feedback is quite limited and is not intended as a substitute for a real oscilloscope or a good multimeter, which will have much higher input impedance, better resolution and range, and higher sampling frequency.) The SLO-scope is not supported in Mac OS or Linux.

 

Included Accessories

The Pololu USB AVR Programmer ships with a 12" (30 cm) 6-pin ISP programming cable and a 6’ (1.8 m) USB A to mini-B cable. It does not ship with software or documentation, but software (including drivers) and documentation can be found under the resources tab.

 

Pololu SLO-scope client for Windows. 

 

 
Pololu USB AVR programmer configuration utility for Windows.  
 
相關下載文件（復制鏈接到瀏覽器）：
 
1.Pololu USB AVR Programmer User’s Guide
http://www.pololu.com/docs/pdf/0J36/pololu_usb_avr_programmer.pdf
2.Pololu AVR Programming Quick Start Guide
http://www.pololu.com/docs/pdf/0J51/avr_programming_quick_start_guide.pdf

File downloads：

1.Pololu AVR Development Bundle for Windows (release 131009)(11MB exe) 
http://www.pololu.com/product/1300/resources
2.USB AVR Programmer Windows Drivers and Software release 121114(11MB pdf) 
http://www.pololu.com/docs/pdf/0J51/avr_programming_quick_start_guide.pdf