- 您現在的位置：買賣IC網 > PDF目錄379828 > CDB4245 (Cirrus Logic, Inc.) 105 dB, 24-Bit, 192 kHz Streo Sudio CODEC PDF資料下載
參數資料
| 型號： | CDB4245 |
| 廠商： | Cirrus Logic, Inc. |
| 元件分類： | Codec |
| 英文描述： | 105 dB, 24-Bit, 192 kHz Streo Sudio CODEC |
| 中文描述： | 105分貝24位192千赫Streo蘇迪奧編解碼器 |
| 文件頁數： | 34/54頁 |
| 文件大小： | 1166K |
| 代理商： | CDB4245 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
CS4245
34
channel noise/signal-to-noise ratios which are only limited by the external mute circuit. The MUTEC pin is an active-
low CMOS driver. See Figure 16 below for a suggested active-low mute circuit.
4.12 Control Port Description and Timing
The control port is used to access the registers, allowing the CS4245 to be configured for the desired operational
modes and formats. The operation of the control port may be completely asynchronous with respect to the audio
sample rates. However, to avoid potential interference problems, the control port pins should remain static if no op-
eration is required.
The control port has 2 modes: SPI and I2C, with the CS4245 acting as a slave device. SPI mode is selected if there
is a high to low transition on the AD0/CS pin, after the RESET pin has been brought high. I2C mode is selected by
connecting the AD0/CS pin through a resistor to VLC or DGND, thereby permanently selecting the desired AD0 bit
address state.
4.12.1 SPI Mode
In SPI mode, CS is the CS4245 chip select signal, CCLK is the control port bit clock (input into the CS4245 from the
microcontroller), CDIN is the input data line from the microcontroller, CDOUT is the output data line to the microcon-
troller. Data is clocked in on the rising edge of CCLK and out on the falling edge.
Figure 17 shows the operation of the control port in SPI mode. To write to a register, bring CS low. The first seven
bits on CDIN form the chip address and must be 1001111. The eighth bit is a read/write indicator (R/W), which
should be low to write. The next eight bits form the Memory Address Pointer (MAP), which is set to the address of
the register that is to be updated. The next eight bits are the data which will be placed into the register designated
by the MAP. During writes, the CDOUT output stays in the Hi-Z state. It may be externally pulled high or low with a
47 k
resistor, if desired.
There is a MAP auto increment capability, enabled by the INCR bit in the MAP register. If INCR is a zero, the MAP
will stay constant for successive read or writes. If INCR is set to a 1, the MAP will auto-increment after each byte is
read or written, allowing block reads or writes of successive registers.
To read a register, the MAP has to be set to the correct address by executing a partial write cycle which finishes (CS
high) immediately after the MAP byte. The MAP auto increment bit (INCR) may be set or not, as desired. To begin
a read, bring CS low, send out the chip address and set the read/write bit (R/W) high. The next falling edge of CCLK
LPF
+V
EE
-V
EE
560
Audio
Out
2 k
10 k
-V
EE
+V
A
MMUN2111LT1
AOUT
MUTEC
AC
Couple
47 k
Figure 16. Suggested Active-Low Mute Circuit
CS4245
相關PDF資料 |
PDF描述 |
|---|---|
| CDB42518 | 110 dB, 192 kHz 6-Ch Codec with S/PDIF Receiver |
| CDB42528 | 114 dB, 192 kHz 6-Ch Codec with S/PDIF Receiver |
| CDB4270 | 24-Bit, 192 kHz Stereo Audio CODEC |
| CDB4271 | 24-Bit, 192 kHz Stereo Audio CODEC |
| CDB4272 | 24-Bit, 192 kHz Stereo Audio CODEC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CDB42518 | 功能描述:音頻 IC 開發工具 Eval Bd RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| CDB42528 | 功能描述:音頻 IC 開發工具 Eval Bd RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| CDB4265 | 功能描述:音頻 IC 開發工具 Eval Bd 192kHz CODEC w/PGA & Input Mux RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| CDB4270 | 功能描述:音頻 IC 開發工具 Eval Bd 105dB 192kHz CODEC RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| CDB4271 | 功能描述:音頻 IC 開發工具 Eval Bd CS4271 RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
發布緊急采購，3分鐘左右您將得到回復。