參數資料
型號： CDB4245
廠商： Cirrus Logic, Inc.
元件分類： Codec
英文描述： 105 dB, 24-Bit, 192 kHz Streo Sudio CODEC
中文描述： 105分貝24位192千赫Streo蘇迪奧編解碼器
文件頁數： 33/54頁
文件大?。?/td> 1166K
代理商： CDB4245
CS4245
33
The auxiliary analog output can source very little current. As current from the AUXOUT pins increases, distortion will
increase. For this reason, a high input impedance buffer must be used on the AUXOUT pins to achieve full perfor-
mance. Refer to the Auxiliary Output Analog Characteristics table on page 18 for acceptable loading conditions.
4.9
De-Emphasis Filter
The CS4245 includes on-chip digital de-emphasis optimized for a sample rate of 44.1 kHz. The filter response is
shown in Figure 15. The frequency response of the de-emphasis curve will scale proportionally with changes in sam-
ple rate, Fs. Please see section 6.3.4 for de-emphasis control.
The de-emphasis feature is included to accommodate audio recordings that utilize 50/15
μ
s pre-emphasis equaliza-
tion as a means of noise reduction.
De-emphasis is only available in Single Speed Mode.
4.10 Internal Digital Loopback
The CS4245 supports an internal digital loopback mode in which the output of the ADC is routed to the input of the
DAC. This mode may be activated by setting the LOOP bit in the Signal Selection register (06h - See page 43). To
use this mode, the ADC and DAC must be operating at the same synchronous sample rate.
When this bit is set, the status of the DAC_DIF[1:0] bits in register 03h will be disregarded by the CS4245. Any
changes made to the DAC_DIF[1:0] bits while the LOOP bit is set will have no impact on operation until the LOOP
bit is cleared, at which time the Digital Interface Format of the DAC will operate according to the format selected by
the DAC_DIF[1:0] bits. While the LOOP bit is set, data will be present on the SDOUT pin in the format selected by
the ADC_DIF bit in register 04h.
4.11 Mute Control
The MUTEC pin becomes active during power-up initialization, reset, muting, if the MCLK2 to LRCK2 ratio is incor-
rect in asynchronous mode or the MCLK1 to LRCK2 ratio is incorrect in synchronous mode, and during power-down.
The MUTEC pin is intended to be used as control for an external mute circuit in order to add off-chip mute capability.
Use of the Mute Control function is not mandatory but recommended for designs requiring the absolute minimum in
extraneous clicks and pops. Also, use of the Mute Control function can enable the system designer to achieve idle
Gain
dB
-10dB
0dB
Frequency
T2 = 15 μs
T1=50 μs
F1
F2
3.183 kHz
10.61 kHz
Figure 15. De-Emphasis Curve
相關PDF資料
PDF描述
CDB42518 110 dB, 192 kHz 6-Ch Codec with S/PDIF Receiver
CDB42528 114 dB, 192 kHz 6-Ch Codec with S/PDIF Receiver
CDB4270 24-Bit, 192 kHz Stereo Audio CODEC
CDB4271 24-Bit, 192 kHz Stereo Audio CODEC
CDB4272 24-Bit, 192 kHz Stereo Audio CODEC
相關代理商/技術參數
參數描述
CDB42518 功能描述:音頻 IC 開發工具 Eval Bd RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB42528 功能描述:音頻 IC 開發工具 Eval Bd RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB4265 功能描述:音頻 IC 開發工具 Eval Bd 192kHz CODEC w/PGA & Input Mux RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB4270 功能描述:音頻 IC 開發工具 Eval Bd 105dB 192kHz CODEC RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB4271 功能描述:音頻 IC 開發工具 Eval Bd CS4271 RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*