- 您現在的位置：買賣IC網 > PDF目錄379828 > CDB42428 (Cirrus Logic, Inc.) 114 dB, 192kHz 8-Ch CODEC WITH PLL PDF資料下載
參數資料
| 型號： | CDB42428 |
| 廠商： | Cirrus Logic, Inc. |
| 元件分類： | Codec |
| 英文描述： | 114 dB, 192kHz 8-Ch CODEC WITH PLL |
| 中文描述： | 114分貝，192kHz的8通道編解碼器與鎖相環 |
| 文件頁數： | 29/67頁 |
| 文件大?。?/td> | 1433K |
| 代理商： | CDB42428 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁
29
CS42428
3.8
Reliable power-up can be accomplished by keeping the device in reset until the power supplies, clocks and
configuration pins are stable. It is also recommended that reset be activated if the analog or digital supplies
drop below the recommended operating condition to prevent power glitch related issues.
Reset and Power-up
When RST is low, the CS42428 enters a low power mode and all internal states are reset, including the
control port and registers, and the outputs are muted. When RST is high, the control port becomes opera-
tional and the desired settings should be loaded into the control registers. Writing a 0 to the PDN bit in the
Power Control Register will then cause the part to leave the low power state and begin operation. If the
internal PLL is selected as the clock source, the serial audio outputs will be enabled after the PLL has set-
tled. See “Power Control (address 02h)” on page 33 for more details.
The delta-sigma modulators settle in a matter of microseconds after the analog section is powered, either
through the application of power or by setting the RST pin high. However, the voltage reference will take
much longer to reach a final value due to the presence of external capacitance on the FILT+ pin. A time
delay of approximately 80ms is required after applying power to the device or after exiting a reset state.
During this voltage reference ramp delay, all serial ports and DAC outputs will be automatically muted.
3.9
As with any high resolution converter, the CS42428 requires careful attention to power supply and ground-
ing arrangements if its potential performance is to be realized. Figure 1 shows the recommended power
arrangements, with VA connected to clean supplies. VD, which powers the digital circuitry, may be run
from the system logic supply. Alternatively, VD may be powered from the analog supply via a ferrite bead.
In this case, no additional devices should be powered from VD.
Power Supply, Grounding, and PCB layout
For applications where the output of the PLL is required to be low jitter, use a separate, low noise analog
+5 V supply for VA, decoupled to AGND. In addition, a separate region of analog ground plane around
the FILT+, VQ, LPFLT, REFGND, AGND, and VA pins is recommended.
Extensive use of power and ground planes, ground plane fill in unused areas and surface mount decoupling
capacitors are recommended. Decoupling capacitors should be as near to the pins of the CS42428 as pos-
sible. The low value ceramic capacitor should be the nearest to the pin and should be mounted on the same
side of the board as the CS42428 to minimize inductance effects. All signals, especially clocks, should be
kept away from the FILT+, VQ and LPFLT pins in order to avoid unwanted coupling into the modulators
and PLL. The FILT+ and VQ decoupling capacitors, particularly the 0.1 μF, must be positioned to mini-
mize the electrical path from FILT+ and REFGND. The CDB42418 evaluation board demonstrates the op-
timum layout and power supply arrangements.
相關PDF資料 |
PDF描述 |
|---|---|
| CDB42438 | 108 dB, 192 kHz 4-in, 6-out TDM CODEC |
| CDB42448 | 108 dB, 192 kHz 6-in, 8-out CODEC |
| CDB4245 | 105 dB, 24-Bit, 192 kHz Streo Sudio CODEC |
| CDB42518 | 110 dB, 192 kHz 6-Ch Codec with S/PDIF Receiver |
| CDB42528 | 114 dB, 192 kHz 6-Ch Codec with S/PDIF Receiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CDB42438 | 功能描述:音頻 IC 開發工具 Eval Bd 108dB 6&8-Ch Mult-Ch CODEC RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| CDB4244 | 制造商:Cirrus Logic 功能描述:EVAL BD 4 INPUT/ 4 OUTPUT CODEC - Boxed Product (Development Kits) 制造商:Cirrus Logic 功能描述:Eval Board |
| CDB42448 | 功能描述:音頻 IC 開發工具 Eval Bd 108dB 8-Ch Mult-Ch CODEC RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| CDB4245 | 功能描述:音頻 IC 開發工具 Eval Bd 192kHz CODEC w/PGA & Input Mux RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| CDB42518 | 功能描述:音頻 IC 開發工具 Eval Bd RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
發布緊急采購，3分鐘左右您將得到回復。