- 您現在的位置：買賣IC網 > PDF目錄374126 > C470XT290-Sxx00-x (Cree, Inc.) XThin㈢ LEDs PDF資料下載
參數資料
| 型號： | C470XT290-Sxx00-x |
| 廠商： | Cree, Inc. |
| 英文描述： | XThin㈢ LEDs |
| 中文描述： | XThin㈢發光二極管 |
| 文件頁數： | 2/6頁 |
| 文件大?。?/td> | 243K |
| 代理商： | C470XT290-SXX00-X |
Copyright 2004-2006 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree,
the Cree logo, GSiC and XThin are registered trademarks, and XT, XT-12, XT-16, XT-18, XT-21, XT-21 and XT-24 are trademarks
of Cree, Inc.
2
CPR3CE Rev. E
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
www.cree.com
Maximum Ratings at T
A
= 25°C
Notes 2&4
DC Forward Current
C
xxx
XT290-S
xx
00-
x
30mA
Peak Forward Current (1/10 duty cycle @ 1kHz)
100mA
LED Junction Temperature
125°C
Reverse Voltage
5 V
Operating Temperature Range
-40°C to +100°C
Storage Temperature Range
-40°C to +100°C
Electrostatic Discharge Threshold (HBM)
Note 3
1000V
Electrostatic Discharge Classification (MIL-STD-883E)
Note 3
Class 2
Typical Electrical/Optical Characteristics at T = 25°C, If = 20mA
Note 4
Part Number
Forward Voltage (V
f
, V)
Reverse Current
[I(Vr=5V), μA]
Full Width Half Max
(
λ
D
, nm)
Min.
Typ.
Max.
Max.
Typ.
C460XT290-S
xx
00-
x
2.7
3.2
3.7
2
21
C470XT290-S
xx
00-
x
2.7
3.2
3.7
2
22
C527XT290-S0100-A
2.7
3.2
3.7
2
35
Mechanical Specifications
C
xxx
XT290-S
xx
00-
x
Description
Dimension
Tolerance
P-N Junction Area (μm)
250 x 250
± 25
Top Area (μm)
200 x 200
± 25
Bottom Area (μm)
300 x 300
± 25
Chip Thickness (μm)
115
± 15
Au Bond Pad Diameter (μm)
105
-5, +15
Au Bond Pad Thickness (μm)
1.2
± 0.5
Back Contact Metal Area (μm)
210 x 210
± 25
Back Contact Metal Thickness (μm) -C (Sn Flux Eutectic)
2.0
± 0.3
Back Contact Metal Thickness (μm) -D (Sn Eutectic)
0.5
± 0.1
Notes:
1.
This product is intended for use in a pre-molded surface mount package. It should be tested in the package and environment
consistent with the final use to validate applicability. CxxxXT290-Sxx00-C and –D are not intended for use where extended reliable
operation in high temperature and high humidity environments is required. For this condition or for use in a leaded radial lamp,
use CxxxXT290-Sxx00-A. See Cree XThin Applications Note for more information.
Maximum ratings are package dependent. The above ratings were determined using a T-1 3/4 package (with Hysol OS4000
epoxy) for characterization. Ratings for other packages may differ. The forward currents (DC and Peak) are not limited by the die
but by the effect of the LED junction temperature on the package. The junction temperature limit of 125°C is a limit of the T-1
3/4 package; junction temperature should be characterized in a specific package to determine limitations. Assembly processing
temperature must not exceed 325°C (< 5 seconds). See Cree XThin Applications Note for more assembly process information.
Product resistance to electrostatic discharge (ESD) according to the HBM is measured by simulating ESD using a rapid avalanche
energy test (RAET). The RAET procedures are designed to approximate the maximum ESD ratings shown. The RAET procedure is
performed on each die. The ESD classification of Class 2 is based on sample testing according to MIL-STD-883E.
All products conform to the listed minimum and maximum specifications for electrical and optical characteristics when assembled
and operated at 20 mA within the maximum ratings shown above. Efficiency decreases at higher currents. Typical values given
are within the range of average values expected by manufacturer in large quantities and are provided for information only. All
measurements were made using lamps in T-1 3/4 packages (with Hysol OS4000 epoxy). Optical characteristics measured in an
integrating sphere using Illuminance E.
Caution: To avoid leakage currents and achieve maximum output efficiency, die attach material must not contact the side of the
chip. See Cree XThin Applications Note for more information.
Specifications are subject to change without notice.
XThin chips are shipped with the junction side down, not requiring a die transfer prior to die attach.
2.
3.
4.
5.
6.
7.
相關PDF資料 |
PDF描述 |
|---|---|
| C4823 | ARM7TDMI" 32-bit MCU with Flash, USB, CAN, 5 timers, ADC, 10 communications interfaces |
| C505RT230-S0100 | RazerThin㈢ LEDs |
| C527RT230-S0100 | RazerThin㈢ LEDs |
| C505RT230-S0200 | RazerThin㈢ LEDs |
| C527RT230-S0200 | RazerThin㈢ LEDs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| C470-Y- L-XL | 制造商:Portwest Clothing 功能描述:HI-VIS 2BAND WAISTCOAT XL |
| C470-Y- S-M | 制造商:Portwest Clothing 功能描述:HI-VIS 2-BAND WAISTCOAT M |
| C470-Y- XXL-XXXL | 制造商:Portwest Clothing 功能描述:HI-VIS 2-BAND W/COAT XXL |
| C4710 | 制造商:VECTRON 制造商全稱:Vectron International, Inc 功能描述:OCXO Low Phase Noise High Stability SC-Cut Crystal Standard |
| C4710-01 | 制造商:HAMAMATSU 制造商全稱:Hamamatsu Corporation 功能描述:HIGH VOLTAGE POWER SUPPLY UNIT |
發布緊急采購，3分鐘左右您將得到回復。