參數資料
型號： ATT3042-100M132I
廠商： Electronic Theatre Controls, Inc.
元件分類： FPGA
英文描述： Field-Programmable Gate Arrays
中文描述： 現場可編程門陣列
文件頁數： 35/80頁
文件大?。?/td> 528K
代理商： ATT3042-100M132I
Data Sheet
February 1997
ATT3000 Series Field-Programmable Gate Arrays
Lucent Technologies Inc.
35
Pin Information
(continued)
Table 5. I/O Pins with Special Functions
Symbol
Name/Description
M2
Mode 2
. This input has a passive pull-up during configuration. Together with M0 and M1, it is
sampled before the start of configuration to establish the configuration mode to be used. After
configuration, this pin becomes a user-programmable I/O pin.
HDC
High During Configuration
. HDC is held at a high level by the FPGA until after configuration. It
is available as a control output indicating that configuration is not yet completed. After
configuration, this pin is a user I/O pin.
LDC
Low During Configuration
. This active-low signal is held at a low level by the FPGA until after
configuration. It is available as a control output indicating that configuration is not yet completed.
It is particularly useful in master mode as a low enable for an EPROM. After configuration, this
pin is a user I/O pin. If used as a low EPROM enable, it must be programmed as a high after
configuration.
INIT
This is an active-low, open-drain output which is held low during the power stabilization and
internal clearing of the configuration memory. It can be used to indicate status to a configuring
microprocessor or, as a wired-AND of several slave mode devices, a hold-off signal for a master
mode device. After configuration, this pin becomes a user-programmable I/O pin.
BCLKIN
This is a direct CMOS level input to the alternate clock buffer (auxiliary buffer) in the lower right
corner.
XTL1
This user I/O pin can be used to operate as the output of an amplifier driving an external crystal
and bias circuitry.
XTL2
This user I/O pin can be used as the input of an amplifier connected to an external crystal and
bias circuitry. The I/O block is left unconfigured. The oscillator configuration is activated by
routing a net from the oscillator buffer symbol output and by the
ORCA
Foundry bit stream
generation program.
CS0
,
CS1
,
CS2,
WS
These four inputs represent a set of signals, three active-low and one active-high, which are
used in the peripheral mode to control configuration data entry. The assertion of all four
generates a write to the internal data buffer. The removal of any assertion clocks in the D[7:0]
data present. In the master parallel mode,
WS
and CS2 are the A0 and A1 outputs. After
configuration, the pins are user-programmable I/O pins.
相關PDF資料
PDF描述
ATT3042-100M44I Field-Programmable Gate Arrays
ATT3042-100M68I Field-Programmable Gate Arrays
ATT3042-100M84I Field-Programmable Gate Arrays
ATT3042-100S132I Field-Programmable Gate Arrays
ATT3042-100S44I Field-Programmable Gate Arrays
相關代理商/技術參數
參數描述
ATT3042-100M44I 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Gate Arrays
ATT3042-100M68I 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Gate Arrays
ATT3042-100M84I 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Gate Arrays
ATT3042-100N100M 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA)
ATT3042-100R132M 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*