- 您現在的位置：買賣IC網 > PDF目錄381425 > AT27C040-15JI (ATMEL CORP) Octal Edge-Triggered D-Type Flip-Flops With 3-State Outputs 20-SSOP -40 to 85 PDF資料下載
參數資料
| 型號： | AT27C040-15JI |
| 廠商： | ATMEL CORP |
| 元件分類： | DRAM |
| 英文描述： | Octal Edge-Triggered D-Type Flip-Flops With 3-State Outputs 20-SSOP -40 to 85 |
| 中文描述： | 512K X 8 OTPROM, 150 ns, PQCC32 |
| 封裝： | PLASTIC, MS-016AE, LCC-32 |
| 文件頁數： | 2/13頁 |
| 文件大小： | 194K |
| 代理商： | AT27C040-15JI |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁
2
AT27C040
0189F–EPROM–4/03
Atmel’s scaled CMOS technology provides low active power consumption, and fast program-
ming. Power consumption is typically 8 mA in active mode and less than 10
μ
A in standby
mode.
The AT27C040 is available in a choice of industry standard JEDEC-approved one-time pro-
grammable (OTP) plastic PDIP, PLCC and TSOP packages. The device features two-line
control (CE, OE) to eliminate bus contention in high-speed systems.
Atmel’s AT27C040 has additional features to ensure high quality and efficient production use.
The Rapid Programming Algorithm reduces the time required to program the part and guaran-
tees reliable programming. Programming time is typically only 100
μ
s/byte. The Integrated
Product Identification Code electronically identifies the device and manufacturer. This feature
is used by industry standard programming equipment to select the proper programming algo-
rithms and voltages.
Switching
Considerations
Switching between active and standby conditions via the Chip Enable pin may produce tran-
sient voltage excursions. Unless accommodated by the system design, these transients may
exceed datasheet limits, resulting in device non-conformance. At a minimum, a 0.1
μ
F high
frequency, low inherent inductance, ceramic capacitor should be utilized for each device. This
capacitor should be connected between the V
CC
and Ground terminals of the device, as close
to the device as possible. Additionally, to stabilize the supply voltage level on printed circuit
boards with large EPROM arrays, a 4.7
μ
F bulk electrolytic capacitor should be utilized, again
connected between the V
CC
and Ground terminals. This capacitor should be positioned as
close as possible to the point where the power supply is connected to the array.
Block Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| AT27C040-15PC | 4-Megabit 512K x 8 OTP EPROM |
| AT27C040-15PI | Octal Edge-Triggered D-Type Flip-Flops With 3-State Outputs 20-TVSOP -40 to 85 |
| AT27C040-15RC | Octal Edge-Triggered D-Type Flip-Flops With 3-State Outputs 20-TVSOP -40 to 85 |
| AT27C040-15RI | 4-Megabit 512K x 8 OTP EPROM |
| AT27C040-15TC | Octal Edge-Triggered D-Type Flip-Flops With 3-State Outputs 20-SOIC -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| at27c040-15lc | 制造商:Atmel Corporation 功能描述:EPROM, 512K x 8, 32 Pin, Ceramic, LCC |
| AT27C040-15LI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 EPROM |
| AT27C040-15LM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 EPROM |
| AT27C040-15LM/883 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 EPROM |
| AT27C040-15PC | 功能描述:可擦除可編程ROM 4M bit RoHS:否 制造商:Maxim Integrated 類型: 存儲容量:1024 bit 組織:1 K x 1 接口類型: 工作電流:5 uA 編程電壓: 工作電源電壓:2.8 V to 6 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:TO-92 |
發布緊急采購，3分鐘左右您將得到回復。