Table 28. VCM Ra" />
參數資料
型號： ADUC7025BSTZ62-RL
廠商： Analog Devices Inc
文件頁數： 51/104頁
文件大?。?/td> 0K
描述： IC MCU 12BIT 1MSPS UART 64-LQFP
標準包裝： 1,500
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 44MHz
連通性： EBI/EMI，I²C，SPI，UART/USART
外圍設備： PLA，PWM，PSM，溫度傳感器，WDT
輸入/輸出數： 30
程序存儲器容量： 64KB（32K x 16）
程序存儲器類型： 閃存
RAM 容量： 2K x 32
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 3.6 V
數據轉換器： A/D 12x12b
振蕩器型： 內部
工作溫度： -40°C ~ 125°C
封裝/外殼： 64-LQFP
包裝： 帶卷 (TR)
ADuC7019/20/21/22/24/25/26/27/28/29
Data Sheet
Rev. F | Page 50 of 104
Table 28. VCM Ranges
AVDD
VREF
VCM Min
VCM Max
Signal Peak-to-Peak
3.3 V
2.5 V
1.25 V
2.05 V
2.5 V
2.048 V
1.024 V
2.276 V
2.048 V
1.25 V
0.75 V
2.55 V
1.25 V
3.0 V
2.5 V
1.25 V
1.75 V
2.5 V
2.048 V
1.024 V
1.976 V
2.048 V
1.25 V
0.75 V
2.25 V
1.25 V
CALIBRATION
By default, the factory-set values written to the ADC offset
(ADCOF) and gain coefficient registers (ADCGN) yield
optimum performance in terms of end-point errors and
linearity for standalone operation of the part (see the
Specifications section). If system calibration is required, it is
possible to modify the default offset and gain coefficients to
improve end-point errors, but note that any modification to the
factory-set ADCOF and ADCGN values can degrade ADC
linearity performance.
For system offset error correction, the ADC channel input stage
must be tied to AGND. A continuous software ADC conversion
loop must be implemented by modifying the value in ADCOF until
the ADC result (ADCDAT) reads Code 0 to Code 1. If the
ADCDAT value is greater than 1, ADCOF should be decremented
until ADCDAT reads 0 to 1. Offset error correction is done
digitally and has a resolution of 0.25 LSB and a range of
±3.125% of VREF.
For system gain error correction, the ADC channel input stage
must be tied to VREF. A continuous software ADC conversion
loop must be implemented to modify the value in ADCGN
until the ADC result (ADCDAT) reads Code 4094 to Code 4095.
If the ADCDAT value is less than 4094, ADCGN should be
incremented until ADCDAT reads 4094 to 4095. Similar to the
offset calibration, the gain calibration resolution is 0.25 LSB
with a range of ±3% of VREF.
TEMPERATURE SENSOR
The ADuC7019/20/21/22/24/25/26/27/28/29 provide voltage
output from on-chip band gap references proportional to
absolute temperature. This voltage output can also be routed
through the front-end ADC multiplexer (effectively an additional
ADC channel input) facilitating an internal temperature sensor
channel, measuring die temperature to an accuracy of ±3°C.
The following is an example routine showing how to use the
internal temperature sensor:
int main(void)
{
float a = 0;
short b;
ADCCON = 0x20;
// power-on the ADC
delay(2000);
ADCCP = 0x10;
// Select Temperature
Sensor as an // input to the ADC
REFCON = 0x01; // connect internal 2.5V
reference // to Vref pin
ADCCON = 0xE4; // continuous conversion
while(1)
{
while (!ADCSTA){};
// wait for end of conversion
b = (ADCDAT >> 16);
// To calculate temperature in °C, use
the formula:
a = 0x525 - b;
// ((Temperature = 0x525 - Sensor
Voltage) / 1.3)
a /= 1.3;
b = floor(a);
printf("Temperature: %d
oC\n",b);
}
return 0;
}
BAND GAP REFERENCE
Each ADuC7019/20/21/22/24/25/26/27/28/29 provides an on-
chip band gap reference of 2.5 V, which can be used for the ADC
and DAC. This internal reference also appears on the VREF pin.
When using the internal reference, a 0.47 F capacitor must be
connected from the external VREF pin to AGND to ensure stability
and fast response during ADC conversions. This reference can
also be connected to an external pin (VREF) and used as a refer-
ence for other circuits in the system. An external buffer is required
because of the low drive capability of the VREF output. A program-
mable option also allows an external reference input on the VREF
pin. Note that it is not possible to disable the internal reference.
Therefore, the external reference source must be capable of
overdriving the internal reference source.
Table 29. REFCON Register
Name
Address
Default Value
Access
REFCON
0xFFFF048C
0x00
R/W
The band gap reference interface consists of an 8-bit MMR
REFCON, described in Table 30.
Table 30. REFCON MMR Bit Designations
Bit
Description
7:1
Reserved.
0
Internal reference output enable. Set by user to
connect the internal 2.5 V reference to the VREF pin.
The reference can be used for an external component
but must be buffered. Cleared by user to disconnect
the reference from the VREF pin.
相關PDF資料
PDF描述
ADUC7025BCPZ62-RL IC MCU 12BIT 1MSPS UART 64-LFCSP
AT91SAM7S256C-AU-999 IC MCU ARM7 256KB FLASH 64LQFP
AT91SAM7X128B-CU-999 IC MCU ARM 128KB FLASH 100TFBGA
VI-J3X-IW-F2 CONVERTER MOD DC/DC 5.2V 100W
VI-J3X-IW-F1 CONVERTER MOD DC/DC 5.2V 100W
相關代理商/技術參數
參數描述
ADUC7026 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU
ADUC7026BST62 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU
ADUC7026BST62-U1 制造商:Analog Devices 功能描述:
ADUC7026BSTZ62 功能描述:IC MCU FLASH 62K W/ANLG 80LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
ADUC7026BSTZ62I 功能描述:IC MCU FLASH 62K ANLG I/0 80LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，WDT 輸入/輸出數:40 程序存儲器容量:96KB（96K x 8） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*