參數資料
型號: ADA4927-1YCP-EBZ
廠商: Analog Devices Inc
文件頁數: 8/24頁
文件大?。?/td> 0K
描述: BOARD EVAL FOR ADA4927-1YCP
標準包裝: 1
每 IC 通道數: 1 - 單
放大器類型: 差分
板類型: 裸(未填充)
已供物品:
已用 IC / 零件: 16-LFCSP 封裝
ADA4927-1/ADA4927-2
Rev. A | Page 16 of 24
THEORY OF OPERATION
The ADA4927 differs from conventional operational amplifiers
in that it has two outputs whose voltages move in opposite
directions and an additional input, VOCM. Moreover, the ADA4927
uses a current feedback architecture. Like a traditional current
feedback op amp, the ADA4927 relies on high open-loop trans-
impedance, T(s), and negative current feedback to force the
outputs to the desired voltages. The ADA4927 behaves much
like a standard current feedback op amp and facilitates single-
ended-to-differential conversions, common-mode level shifting,
and amplifications of differential signals. Also, like a current
feedback op amp, the ADA4927 has low input impedance
summing nodes, which are actually emitter-follower outputs.
The ADA4927 outputs are low impedance, and the closed-loop
output impedances are equal to the open-loop output impedances
divided by a factor of 1 + loop gain. Because it uses current
feedback, the ADA4927 manifests a nominally constant feed-
back resistance, bandwidth product. In other words, the closed-
loop bandwidth and stability of the ADA4927 depend primarily
on the feedback resistor value. The closed-loop gain equations
for typical configurations are the same as those of comparable
voltage feedback differential amplifiers. The chief difference is
that the ADA4927 dynamic performance depends on the feed-
back resistor value rather than on the noise gain. Because of
this, the elements used in the feedback loops must be resistive
with values that ensure stability and sufficient bandwidth.
Two feedback loops are employed to control the differential and
common-mode output voltages. The differential feedback loops
use a current feedback architecture with external resistors and
control only the differential output voltage. The common-mode
feedback loop is internal, uses voltage feedback, and controls only
the common-mode output voltage. This architecture makes it
easy to set the output common-mode level to any arbitrary
value within the specified limits. The output common-mode
voltage is forced, by the internal common-mode loop, to be
equal to the voltage applied to the VOCM input.
The internal common-mode feedback loop produces outputs
that are highly balanced over a wide frequency range without
requiring tightly matched external components. This results
in differential outputs that are very close to the ideal of being
identical in amplitude and are exactly 180° apart in phase.
DEFINITION OF TERMS
+IN
–IN
+OUT
–OUT
+DIN
–FB
+FB
–DIN
VOCM
RG
RF
RG
VOUT, dm
RL, dm
RF
ADA4927
07
57
4-
0
46
Figure 46. Circuit Definitions
Differential Voltage
Differential voltage refers to the difference between two
node voltages. For example, the output differential voltage (or
equivalently, output differential-mode voltage) is defined as
VOUT, dm = (V+OUT VOUT)
where V+OUT and VOUT refer to the voltages at the +OUT and
OUT terminals with respect to a common ground reference.
Similarly, the differential input voltage is defined as
VIN, dm = (+DIN (DIN))
Common-Mode Voltage
Common-mode voltage refers to the average of two node voltages
with respect to the local ground reference. The output
common-mode voltage is defined as
VOUT, cm = (V+OUT + VOUT)/2
Balance
Output balance is a measure of how close the differential signals
are to being equal in amplitude and opposite in phase. Output
balance is most easily determined by placing a well-matched
resistor divider between the differential voltage nodes and
comparing the magnitude of the signal at the divider midpoint
with the magnitude of the differential signal (see Figure 44). By
this definition, output balance is the magnitude of the output
common-mode voltage divided by the magnitude of the output
differential mode voltage.
dm
OUT
cm
OUT
V
Error
Balance
Output
,
Δ
=
相關PDF資料
PDF描述
ECM12DRTI-S13 CONN EDGECARD 24POS .156 EXTEND
1-1589476-0 CONN RCPT 15POS 28AWG 3M
ECM12DRKI-S13 CONN EDGECARD 24POS .156 EXTEND
VE-JTL-EY CONVERTER MOD DC/DC 28V 50W
ADA4851-4YRU-EBZ BOARD EVAL FOR ADA4851-4YRU
相關代理商/技術參數
參數描述
ADA4927-1YCPZ-R2 制造商:Analog Devices 功能描述:SP Amp Differential ADC Driver Single 11V 16-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:SP AMP DIFFERENTIAL ADC DRVR SGL 11V 16LFCSP EP - Tape and Reel 制造商:Analog Devices 功能描述:ANAADA4927-1YCPZ-R2 ULTRALW DISTORTION C 制造商:Analog Devices 功能描述:OP AMP CF DIFF 65MA LN 16LFCSP 制造商:Analog Devices 功能描述:OP AMP, CF, DIFF, 65MA, LN, 16LFCSP 制造商:Analog Devices 功能描述:OP AMP, CF, DIFF, 65MA, LN, 16LFCSP; No. of Amplifiers:1; Input Offset Voltage:1.3mV; Bandwidth:2.3GHz; Amplifier Case Style:LFCSP; No. of Pins:16; Supply Voltage Range:4.5V to 11V; Slew Rate:5000V/s; Supply Current:20mA; Operating ;RoHS Compliant: Yes
ADA4927-1YCPZ-R2 制造商:Analog Devices 功能描述:IC DIFF AMP 2.3GHZ 5000V/ LFCSP-16
ADA4927-1YCPZ-R7 功能描述:IC OPAMP CF DIFF 65MA LN 16LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源,單路/雙路(±):3 V ~ 32 V,±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR
ADA4927-1YCPZ-RL 功能描述:IC OPAMP CF DIFF 65MA LN 16LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:13 V/µs 增益帶寬積:3MHz -3db帶寬:- 電流 - 輸入偏壓:65pA 電壓 - 輸入偏移:3000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:- 電壓 - 電源,單路/雙路(±):7 V ~ 36 V,±3.5 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:8-DIP(0.300",7.62mm) 供應商設備封裝:8-PDIP 包裝:管件
ADA4927-2 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultralow Distortion Current Feedback Differential ADC Driver