
12
IN
DEVELOPMENT
7.0 DC OUTPUT ELECTRICAL CHARACTERISTICS (Pre- and Post-Radiation)*
(VDDQn = +2.5V + 10%; VDD = +3.3V + 0.3V; TC = -55°C to +125°C) (Note 1)
(VDDQn = +3.3V + 0.3V; VDD = +3.3V + 0.3V; TC = -55°C to +125°C)
Notes: * Post-radiation performance guaranteed at 25
°C per MIL-STD-883 Method 1019, Condition A up to a TID level of 1.0E6 rad(Si).
1. Unless otherwise noted, these tests are performed with VDD and VDDQn at their minimum levels.
2. Supplied as a design limit. Neither guaranteed nor tested.
3. When measuring the dynamic supply current, all outputs are loaded in accordance with the equivalent test load defined in figure 10.
4. Capacitance is measured for initial qualification and when design changes may affect the input/output capacitance. Capacitance is measured between the designated
terminal and VSS at frequency of 1MHz and a signal amplitude of 50mV rms maximum.
Symbol
Description
Conditions
Min.
Max.
Units
VOL
Output low voltage
IOL = 12mA (PE/HD = LOW or HIGH); (Pins: nQ[1:0])
--
0.4
V
IOL = 20mA (PE/HD = MID); (Pins: nQ[1:0])
--
0.4
V
IOL = 2mA (Pins: LOCK)
--
0.4
V
IOH DDQn = +2.25V)
2.0
--
VOH
High-level output
voltage
IOH = -12mA (PE/HD=LOWor HIGH); (Pins: nQ[1:0]; VDDQn = +2.375V)
2.0
--
V
IOH = -16mA (PE/HD = MID); (Pins: nQ[1:0]; VDDQn = +2.25V)
2.0
--
V
IOH = -20mA (PE/HD = MID); (Pins: nQ[1:0]; VDDQn = +2.375V)
2.0
--
V
IOH = -2mA (Pins: LOCK)
2.4
--
V
IOSQn
2
Short-circuit output
current
VO = VDDQn or VSS; VDDQn = +2.75V; PE/HD = MID
-500
500
mA
VO = VDDQn or VSS; VDDQn = +2.75V; PE/HD = LOW or HIGH
-300
300
mA
IDDOP
3
Dynamic supply
current
@200MHz (FS = HIGH); VDD = Max; VDDQn = +2.75V; CL = 40pF/output
--
250
mA
@100MHz (FS = MID); VDD = Max; VDDQn = +2.75V; CL = 40pF/output
--
150
mA
@50MHz (FS = LOW); VDD = Max; VQn = +2.75V; CL = 40pF/output
--
100
mA
COUT
4
Output pin capacitance
f = 1MHz @ 0V; VDD = Max; VDDQn = +2.75V
15
pF
Symbol
Description
Conditions
Min.
Max.
Units
VOL
Output low voltage
IOL = 12mA (PE/HD = LOW or HIGH); (Pins: nQ[1:0])
--
0.4
V
IOL = 24mA (PE/HD = MID); (Pins: nQ[1:0])
--
0.4
V
IOL = 2mA (Pins: LOCK)
--
0.4
V
VOH
High-level output
voltage
IOH = -12mA (PE/HD = LOW or HIGH); (Pins: nQ[1:0])
2.4
--
V
IOH = -24mA (PE/HD = MID); (Pins: nQ[1:0])
2.4
--
V
IOH = -2mA (Pins: LOCK)
2.4
--
V
IOSQn
2
Short-circuit output
current
VO = VDDQn or VSS; VDDQn = +3.6V; PE/HD = MID
-600
600
mA
VO = VDDQn or VSS; VDDQn = +3.6V;
PE/HD = LOW or HIGH
-300
300
mA
IDDOP
3
Dynamic supply
current
@200MHz (FS = HIGH); VDD = Max; VDDQn = +3.6V; CL = 40pF/output
--
400
mA
@100MHz (FS = MID); VDD = Max; VDDQn = +3.6V; CL = 40pF/output
--
230
mA
@50MHz (FS = LOW); VDD = Max; VDDQn = +3.6V; CL = 40pF/output
--
150
mA
COUT
4
Output pin capacitance
f = 1MHz @ 0V; VDD = Max; VDDQn = +3.6V
15
pF